5.8.1.2.4 Edge Protection on Platforms 1½ inches or less in Height. Edge protection is not required on platforms 1 ½ inches or less in height.
Search Results "Curb Ramp Surface"
-
5.8.1.2.4 Edge Protection on Platforms 1½ inches or less in Height
-
5.8.1.2.4 Edge Protection on Platforms 1½ inches or less in Height Recommendations
5.8.1.2.4 Edge Protection on Platforms 1½ inches or less in Height Recommendations The Committee recommends that no edge protection be required on platforms of 1½ inches or less...
-
§ 37.42(f)
vertical gap is more than 5/8 inch, measured when the vehicle is at rest, the horizontal and vertical gaps between the car floor and the boarding platform must be mitigated by a bridge plate, ramp...
-
DSA Drawing 11B-406.6-8 Cut-Through Median with No Gutters (2016 CBC)
Requires the Premium User plan or above. (Login or upgrade your account!) -
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment On imaging equipment, the transfer surface is oriented along the long dimension of the surface where...
-
11B-809.9.1 Clear floor space
Clear floor spaces 30 inches (762 mm) by 48 inches (1219 mm), with centerlines aligned with the centerline of the work surface, appliance, sink or fixture, shall be provided in the following...
-
KIROLA v. THE CITY AND COUNTY OF SAN FRANCISCO
N.D. Cal. UNITED STATES DISTRICT COURT FOR THE NORTHERN DISTRICT OF CALIFORNIA OAKLAND DIVISION Case No: C 07-3685 SBA 11-26-2014 IVANA KIROLA, et al.,...
-
NYC Board of Elections: Video 4 - Accessibility Maintenance
-
Sales and Service Counters, Teller Windows, Information Counters [7.2]
Sales and Service Counters, Teller Windows, Information Counters [7.2] ADAAG generally specifies accessible counter heights up to 34 inches [4.32] but allows a height up to 36...
-
1.1.7 Measurement of parking areas
1.1.7 Measurement of parking areas. Only accessible access aisles and passenger loading zones that are part of a larger parking area need to be measured. These areas should be...
-
M305.3.1 Length (Section-by-Section Analysis)
In the MDE NPRM, the Access Board proposed a gripping surface length of four inches minimum for horizontal standing supports. No public comments were submitted on this requirement....
-
1009.2 Continuity and components
Ramps complying with Section 1012, and Chapter 11A, Sections 1114A and 1122A, or Chapter 11B, 11B-405, as applicable. Areas of refuge complying with Section 1006....
-
NYC Board of Elections: Video 6 - Verifying Temporary Solutions
-
M301.2.2 Sunset
The low transfer position height, Item A of M301.2.1, shall cease to have effect on [Insert date 5 years after date of publication in the Federal Register].
-
AIAU Accessible Architecture: Designing for Success (Parts 1-3)
In Part 2, go in depth on compliance issues regarding accessible routes, ramps, parking spaces, protruding objects, doors and clear floor space, controls, and counters....
-
11B-705.1.1.4 Resiliency
Detectable warning surfaces shall differ from adjoining surfaces in resiliency or sound-on-cane contact....
-
11B-705.1.1.4 Resiliency
Detectable warning surfaces shall differ from adjoining surfaces in resiliency or sound-on-cane contact....
-
AquaTrek2 ADA Wading Pool Ramp
AquaTrek2 ADA Wading Pool Ramp The same quality ramp as our Standard AquaTrek2 products, specifically modified to meet the ADA standard for Wading Pool Access....
-
11B-805 Medical care and long-term care facilities
SECTION 11B-805 Medical care and long-term care facilities 11B-805.7 Built-in cabinets and work surfaces....
-
4.1.7(1)(b) Definition
(b) Definition. A qualified historic building or facility is a building or facility that is:
-
M301.2.3 Size (Section-by-Section Analysis)
As discussed in Section IV.B.1.c (Significant Changes – Transfer Surface Size), in the final rule the Access Board has revised this provision to account for the two types of transfer surfaces...
-
11B-1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
11B-1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
