Hinges: All hinges are full length, heavy duty, stainless steel piano type hinges. Collars: #22 ga stainless steel finished to match cabinet....
Search Results "Hinge Side Clearance"
Filters
Commonly Searched Documents
-
AJW Architectural Products U684 Series Dual Toilet Tissue Dispenser & Sanitary Napkin Disposal - Recessed
-
Greenfields Outdoor Fitness Two-Person Accessible Combo Butterfly and Reverse Fly GR2005-1-48E-W (2 Configurations)
Reverse Fly GR2005-1-48E-W Target muscle - secondary muscles Strengthens chest, shoulders, back, arms, and upper and mid-abs Configuration A Accessible side...
-
11B-904.3.2 Counter
The top of the counter edge protection shall be 2 inches (51 mm) maximum above the top of the counter surface on the aisle side of the check-out counter....
-
T402.7 Edge Guards
Ramps and bridgeplates shall provide edge guards continuously along each side of the ramp or bridgeplate to within 3 inches (75 mm) of the end of the ramp or bridgeplate that is deployed...
-
G. Compartment Size
.: diagonal or side approaches)? [ADA Stds. 4.17.3] Yes __ No __ N/A __ Comments: ___________________________________________...
-
R207.1 General
The curb ramp (excluding any flared sides) or blended transition shall be contained wholly within the width of the pedestrian street crossing served....
-
11B-410.1 General
Because an accessible route requires an 80 inch (2030 mm) vertical clearance, care should be taken in selecting lifts as they may not be equally suitable for use by people using wheelchairs...
-
403 Walking Surfaces
The requirements for walking surfaces derive from existing specifications for accessible routes covering floor or ground surfaces, slope, changes in level, and clearances....
-
11B-410.1 General
Because an accessible route requires an 80 inch (2030 mm) vertical clearance, care should be taken in selecting lifts as they may not be equally suitable for use by people using wheelchairs...
-
11B-410.1 General
Because an accessible route requires an 80 inch (2030 mm) vertical clearance, care should be taken in selecting lifts as they may not be equally suitable for use by people using wheelchairs...
-
Design Opportunity
The pictured example vanity using the stock bracket and dimensions shown in section view may not provide the required minimum 8" deep knee clearance at 27" AFF under the vanity top (306)...
-
Guidelines for Requirement 5
The inclusion of this additional specification for side approach is consistent with the comparable provisions in the ANSI Standard....
-
11B-504.8 Floor identification
11B-703.2 _|Raised Characters|_, 11B-703.3 _|Braille|_ and 11B-703.5 _|Visual Characters|_ shall be located at the landing of each floor level, placed adjacent to the door on the latch side...
-
11B-604.5.2 Rear wall
The rear wall grab bar shall be 36 inches (914 mm) long minimum and extend from the centerline of the water closet 12 inches (305 mm) minimum on one side and 24 inches (610 mm) minimum on...
-
11B-504.8 Floor identification
11B-703.2 _|Raised Characters|_, 11B-703.3 _|Braille|_ and 11B-703.5 _|Visual Characters|_ shall be located at the landing of each floor level, placed adjacent to the door on the latch side...
-
11B-604.5.2 Rear wall
The rear wall grab bar shall be 36 inches (914 mm) long minimum and extend from the centerline of the water closet 12 inches (305 mm) minimum on one side and 24 inches (610 mm) minimum on...
-
1023.9 Stairway identification signs
braille floor identification signs that comply with Chapter 11A, Section 1143A or Chapter 11B shall be located at the landing of each floor level, placed adjacent to the door on the latch side...
-
Smooth Surface
Section 404.2.10 requires that swinging doors and gates have a smooth surface on the push side that extends their full width....
-
11B-406.5.3 Landings
The landing clear width shall be at least as wide as the curb ramp, excluding any flared sides, or the blended transition leading to the landing....
-
Magnuson Group 2000 Series Magazine Racks
Available with one, two, three or four pocket configurations, these racks can be installed with or without wood side panels....
-
Dispersion Requirements
Like the proposed rule, specifications are provided for horizontal (side to side) and vertical (front to back) dispersion....
-
4.4.2 Mammography Equipment and Scooters
However, the steering column and other front components of many scooters prevent this necessary proximity without the woman swiveling their seat to a side position....
-
B. Summary of Major Provisions and Organization of Technical Criteria
The Access Board has divided the MDE Standards into separate technical criteria based on how the diagnostic equipment is used by the patient: (1) supine, prone, or side lying position (M301...
-
G. Sleeping Areas
An accessible route is needed to provide access to each accessible cot and a clear space at least 36 inches wide is needed along the side of the cot to make it possible to transfer between...
