the diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
Search Results "Surface Hazard"
Filters
Commonly Searched Documents
-
M302.4.2 Clearance Around Base
-
M301.4.2 Clearance Around Base
base of diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
1002.4.4.3 Permitted Protrusions in Wheelchair Spaces
protrude a distance of 6 inches (150 mm) maximum along the front of the wheelchair space, where located 9 inches (230 mm) minimum and 27 inches (685 mm) maximum above the floor or ground surface...
-
MEASUREMENT TECHNIQUE
MEASUREMENT TECHNIQUE The depth and width are measured along the centerlines of the seat, and the height from the floor to the highest point of the transfer surface: The depth...
-
14.2 Q. If both open and covered parking spaces are provided, how many of each type must be accessible?
., surface parking or garage, that are provided for other residents of the project....
-
801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
4.8.1 General
One fixed showerhead shall be 48 inches (1220 mm) above the floor or ground surface, and one fixed shower head shall be 72 inches (1830 mm) minimum above the floor or ground surface....
-
68.30(3) Van Accessible Parking at Garages Constructed Prior to April 1994
If additional surface parking is provided, the required van accessible parking spaces shall be located on a surface lot in closest proximity to the accessible public entrance serving the...
-
11B-1002.4.4.3 Permitted protrusions in wheelchair spaces
protrude a distance of 6 inches (152 mm) maximum along the front of the wheelchair space, where located 9 inches (229 mm) minimum and 27 inches (686 mm) maximum above the floor or ground surface...
-
11B-801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
11B-1002.4.4.3 Permitted protrusions in wheelchair spaces
protrude a distance of 6 inches (152 mm) maximum along the front of the wheelchair space, where located 9 inches (229 mm) minimum and 27 inches (686 mm) maximum above the floor or ground surface...
-
Mockett DH4/DH5 Installation Video
Lightweight, yet sturdy and durable, these subtle complementary pulls will enhance the overall design of any door surface....
-
Transition Plate
A sloping pedestrian walking surface located at the end(s) of a gangway....
-
106.5.72 Transition Plate
A sloping pedestrian walking surface located at the end(s) of a gangway....
-
T303.3 Cross Section
Gripping surfaces shall have a cross section complying with T303.3....
-
M302.3 Supports
Transfer supports, armrests, and reclining surfaces shall comply with M302.3....
-
M301.3 Supports
Transfer supports, stirrups, and reclining surfaces shall comply with M301.3....
-
Stowage of Wheelchairs and Mobility Aids
Carriers must accept battery-powered wheelchairs (and other battery-powered mobility aids) in baggage, subject to applicable hazardous materials rules....
-
Viewing Areas
When the surface isn't paved or built with boards, allow grades up to 1:33 (3 percent) in any direction if needed for proper drainage....
-
M305.2.2 Length (Section-by-Section Analysis)
extend horizontally along the transfer surface to within three inches, to allow for manufacturing tolerances....
-
4. Comparison of Proposed Technical Provisions Applicable to Shared Use Paths and AASHTO Guide
R302.7 Surfaces....
-
M302.3 Supports
Transfer supports, leg supports and reclining surfaces shall comply with M302.3....
-
Ramp
A walking surface that has a running slope steeper than 1:20....
-
M301.3 Supports
Transfer supports, leg supports, and reclining surfaces shall comply with M301.3....