This standard is referenced in the play areas requirements of this document when an accessible surface is required inside a play area use zone where a fall attenuating surface is also required...
Search Results "Ground Surface"
-
ASTM
-
ASTM
This standard is referenced in the play areas requirements of this document when an accessible surface is required inside a play area use zone where a fall attenuating surface is also required...
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
4.15.2* SPOUT HEIGHT
Spouts shall be no higher than 36 in (915 mm), measured from the floor or ground surfaces to the spout outlet (see Fig. 27(a))....
-
AJW Architectural Products U593 1.6 Gallon Sanitary Napkin Disposal w/ Mounted Shelf - Surface Mounted
Shelf: Fabricated of #22 ga stainless steel with 1/2" bends, hemmed and ground smooth. Shelf supported by two stainless steel brackets. Can be mounted on either side of disposal....
-
19. Please indicate the duration of the warranty/guarantees offered for the surface product used by the sales representative/vendor
Please indicate the duration of the warranty/guarantees offered for the surface product used by the sales representative/vendor....
-
Bobrick B-279 ClassicSeries® Surface-Mounted Waste Receptacle
B-279 ClassicSeries® Surface-Mounted Waste Receptacle Satin-finish stainless steel. Bottom edges hemmed for safety....
-
Bobrick TrimLineSeries ADA Surface-Mounted Hand Dryer B-7128.115V
Durable, 22-gauge galvanized steel with exposed surface, type 304 satin-finish stainless steel cover having #4 satin-finish vertical grain with black plastic trim, automatic sensor, dual...
-
904.4.1 Parallel Approach
A portion of the counter surface that is 36 inches (915 mm) long minimum and 36 inches (915 mm) high maximum above the finish floor shall be provided....
-
11B-308.3.1 Unobstructed
Where a clear floor or ground space allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches (1219 mm) maximum and the low side...
-
405.9.2 Curb or Barrier
A curb or barrier shall be provided that prevents the passage of a 4 inch (100 mm) diameter sphere, where any portion of the sphere is within 4 inches (100 mm) of the finish floor or ground...
-
T402.8.1 Deployment to Roadways or to Curb Height Boarding and Alighting Areas
The running slope of ramps and bridgeplates used for deployment to the roadway or to curb-height boarding and alighting areas shall be 1:6 maximum, as measured to ground level with the non-rail...
-
405.9.2 Curb or Barrier
A curb or barrier shall be provided that prevents the passage of a 4 inch (100 mm) diameter sphere, where any portion of the sphere is within 4 inches (100 mm) of the finish floor or ground...
-
Armor-Tile Tactile Systems Cast In Place Detectable Warning Surface System
Armor-TileTM Cast in Place is the world leader in tactile walking surface indicators systems....
-
4.32 SEATING, TABLES, AND WORK SURFACES
[See subsections ...]
-
4.29.2* TACTILE WARNINGS ON WALKING SURFACES
(Reserved).
-
A4.29.2 TACTILE WARNINGS ON WALKING SURFACES
(Reserved).
-
A4.32 SEATING, TABLES, AND WORK SURFACES
[See subsections ...]
-
11B-809.9.7 Exposed pipes and surfaces
Exposed water supply and drain pipes under sinks and lavatories shall comply with Section 11B-606.5.
-
Clear Tread Width of Trails
Clear tread width is the width of traveled surface between obstacles on the ground and above the ground (figure 129). Provide at least 36 inches (915 millimeters) of clear tread width....
