Welded Dual Moment corner construction with four Sigma deep penetration and fillet welds, and additional mechanical fastening all provide one of the strongest door constructions in the industry...
Search Results "Elevator Car Door"
Filters
Commonly Searched Documents
-
Kawneer North America 1040 Sliding Mall Front Door
-
11B-233.3.1.2.6 Public housing facility site impracticality
The site impracticality tests in this section may be used to determine the number of required residential dwelling units with adaptable features in buildings without an elevator, located...
-
§ 36.304(b)(18)
(18) Creating designated accessible parking spaces;
-
Sec.36.304(b)(18)
(18) Creating designated accessible parking spaces;
-
F208 Parking Spaces
[See subsections ...]
-
Must the minimum number of spaces be determined separately for each parking facility on a site or can it be based on the collective total of spaces provided on a site?
The minimum number of accessible parking spaces, including van accessible spaces, must be calculated separately for each parking facility on a site. Spaces required for one parking...
-
§ 38.107(a)
(a) If a restroom is provided for the general public, it shall be designed so as to allow a person using a wheelchair or mobility aid to enter and use such restroom as specified in...
-
§ 38.113(d)(4) Exception
(4) Exception. Retrofitted vehicles shall be coordinated with the platform in existing stations such that the horizontal gap shall be no greater than 4 inches and the height of the...
-
§ 38.123(a)(4)
(4) Faucets and flush controls shall be operable with one hand and shall not require tight grasping, pinching, or twisting of the wrist. The force required to activate controls shall...
-
§ 38.107(a)(2)
(2) The height of the water closet shall be 17 inches to 19 inches measured to the top of the toilet seat. Seats shall not be sprung to return to a lifted position.
-
NABCO GT300-02L Center Pivot Outswing LH
Requires the Premium User plan or above. (Login or upgrade your account!) -
NABCO GT300-04 Center Pivot Simultaneous Pair Outswing
Requires the Premium User plan or above. (Login or upgrade your account!) -
NABCO GT300-01L Center Pivot Inswing RH Single With Panic
Requires the Premium User plan or above. (Login or upgrade your account!) -
NABCO GT300-02R Center Pivot Outswing RH
Requires the Premium User plan or above. (Login or upgrade your account!) -
NABCO GT300-03 Center Pivot Simultaneous Pair Inswing With Panic
Requires the Premium User plan or above. (Login or upgrade your account!) -
NABCO GT300-05 Center Pivot Dual Inswing Outswing
Requires the Premium User plan or above. (Login or upgrade your account!) -
BEST Door Lever Hardware Cylindrical Locks - 5K
• Underwriters Laboratories®: 5K series – Listed by Underwriters Laboratories for use on 3 Hr, A label for single (4’ x 8’) doors....
-
Wikk Industries Ingress'r Automatic Door Control
In libraries and government buildings, where people are typically moving boxes of paperwork from one area to another, being able to open the door with only a bump from the hip will be welcomed...
-
1007.6 Areas of refuge
Every required area of refuge shall have direct access to a stairway complying with Sections 1007.3 or an elevator complying with Section 1007.4....
-
Figure 404.2.3 Clear Width of Doorways – Drawing from the U.S. Access Board
-
Figure 410.6 Platform Lift Doors and Gates – Drawing from the U.S. Access Board
-
QUESTION: WHEN DO THE REQUIREMENTS OF SECTION 37.42 BEGIN TO APPLY?
ANSWER: The performance standard and other requirements of section 37.42(a) apply to stations that are approved for entry into final design or that begin construction or...
-
Hager Companies Round Wrought Door Pull 4
Round Wrought Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2" (64 mm) Clearance available on special order. Add prefix ''H'' to number....
-
Hager Companies Round Wrought Door Pull 3
Round Wrought Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2" (64 mm) Clearance available on special order. Add prefix ''H'' to number....
