The bench is a perfect companion to the MultipliCITY table under which it efficiently slides....
Search Results "Adjustable Height Exam Table"
Filters
Commonly Searched Documents
-
Landscape Forms Inc. Multiplicity Bench Collection
-
Caroma® USA Caravelle Smart 270 One Piece Toilet
cleaning Fully concealed Massive Signature Trapway - More than double the size of industry stand, makes the Caravelle Smart 270 One piece virtually unblockable 10" - 12" Adjustable...
-
How to Set Up the Nest Learning Thermometer
This walk-through of the Nest Learning Thermostat setup process includes connecting your Nest Learning Thermostat to Wi-Fi, answering setup questions, adjusting the temperature and going...
-
Getting In
Sometimes it's fairly easy to add surfacing material, shim up the deck or porch boards, or use asphalt or concrete to bring the access route up to the height of the building floor....
-
Rise [§405.6]
Rise [§405.6] The height of runs is limited (30” max.), but there is no limit on the number of runs a ramp may have....
-
New Accessible Handpump for Campgrounds
The pump's control heights should be between 28 and 40 inches from the ground....
-
4.3 Reach Ranges
4.3 Reach Ranges Figures 14-15 and Table 4 show the standards from the four countries related to reach from a wheeled mobility device....
-
N. Equal Access for Handicapped Students
However, where possible, a recipient must adjust those requirements to the needs of individual handicapped students....
-
10.3.1(7)*
(7)* Automatic fare vending, collection and adjustment (e.g., add-fare) systems shall comply with 4.34.2, 4.34.3, 4.34.4, and 4.34.5....
-
Sensory Issues
purification system Modify or create a fragrance-free workplace policy Allow telework Fluorescent light sensitivity: Move employee to a private area to allow for personal adjustment...
-
1132A.4 Level floor or landing
Primary entry doors, required exit doors or secondary exterior doors with changes in height between the interior surface or floor level and the exterior surface or floor level shall comply...
-
705.1.1 Dome Size
a base diameter of 0.9 inch (23 mm) minimum and 1.4 inches (36 mm) maximum, a top diameter of 50 percent of the base diameter minimum to 65 percent of the base diameter maximum, and a height...
-
9.6 ATTENDANCE-RECORDING EQUIPMENT
Time clocks, card racks, log books, and other work assignment or attendance-recording equipment used by people in wheelchairs must be installed at a height no more than 48 in (1220 mm) above...
-
11B-221.2.1.3 Other boxes
In boxes other than those required to comply with Section 11B-221.2.1.2, the total number of wheelchair spaces required shall be determined in accordance with Table 11B-221.2.1.1....
-
903 Benches
Specifications for benches address clear floor or ground space (903.2), size (903.3), back support (903.4), height (903.5), structural strength (903.6), and slip resistance in wet locations...
-
1134A.7 Water closets
The grab bar reinforcement shall be a minimum of 6 inches (152.4 mm) nominal in height. The backing shall be a minimum of 40 inches (1016 mm) in length....
-
1011.3 Operable Parts
This section requires operable parts of outdoor constructed features to comply with the technical requirements for the height of operable parts in 309.3 of the Architectural Barriers Act...
-
302.2 Carpet
Pile height shall be ½ inch (13 mm) maximum. Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge....
-
Tread Obstacles [1017.5]
The limit on the height of tread obstacles on trails, passing spaces, and resting intervals is based on the surface material used....
-
1003.2.12.2 Opening limitations
Open guards shall have balusters or ornamental patterns such that a 4-inch-diameter (102 mm) sphere cannot pass through any opening up to a height of 34 inches (864 mm)....
-
302.2 Carpet
Pile height shall be ½ inch (13 mm) maximum. Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge....
-
1134A.7, Item 2
The grab bar reinforcement shall be a minimum of 6 inches (152.4 mm) nominal in height. The backing shall be a minimum of 40 inches (1016 mm) in length....
-
4.34.3(2)(b) Reach Depth More Than 10 in
vertical plane perpendicular to the edge of the unobstructed clear floor space at the farthest protrusion of the automated teller machine or surround is more than 10 in (255 mm), the maximum height...
-
1134A.7, Item 2
The grab bar reinforcement shall be a minimum of 6 inches (152.4 mm) nominal in height. The backing shall be a minimum of 40 inches (1016 mm) in length....
