In its proposed rule, the Access Board proposed that the “height of the transfer surface during patient transfer shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured...
Search Results "Smooth Surface"
-
ALIGNMENT OF 19-INCH RECOMMENDATION WITH ACCESS BOARD PROPOSED RULEMAKING
-
11B-1003.2.1 Boat slips
The vertical distance is 10 feet (3050 mm) between the elevation where the gangway departs the landside connection and the elevation of the pier surface at the lowest water level....
-
Boat Slips: ADA Standard Section 1003.2.1
Where handrail extensions are provided on gangways or transition plates, the handrail extensions shall not be required to be parallel with the ground or floor surface. 7....
-
11B-1003.2.1 Boat slips
The vertical distance is 10 feet (3050 mm) between the elevation where the gangway departs the landside connection and the elevation of the pier surface at the lowest water level....
-
5.4.1.2 Transfer and Positioning Support Location for Imaging Equipment
Transfer supports should be provided for imaging equipment with transfer surfaces with depths of less than or equal to 24 inches....
-
Cavity Sliders USA Inc. CS SofStop™ Insert Track
The CS SofStop™ pocket insert track is a smooth running, soft closing system designed specifically for pocket doors. ...
-
American Specialties Adjustable Tilt Mirror 0600T
Angle frame fabricated of 18 gauge stainless steel with corners welded and ground smooth. Tilts a full 6" (152 mm) with bottom mounted on full width stainless steel piano hinge....
-
Slope
The incline of a surface....
-
Slope
The incline of a surface. ...
-
Edge Protection
Edge Protection Where railings, guards, or handrails are provided, edge protection must be provided and extend a minimum of 2 inches above the ground or deck surface....
-
22. How can I get copies of the ASTM standards that apply to play areas?
American Society for Testing and Materials, 100 Bar Harbor Drive, West Conshohocken, Pennsylvania 19428, www.astm.org: ASTM F 1292-99 Standard Specification for Impact Attenuation of Surface...
-
SEAT HEIGHT MEASUREMENT DETAIL
Note that examination tables and chairs only use bolsters on certain areas of the transfer surface....
-
1.3.2 Focus Following NPRM Comments
This review identified four major issue areas for the MDE Advisory Committee to address, as follows: Transfer surface height and size Permitted obstructions to the transfer surface...
-
I. Public Toilet Rooms
In all public and common use toilet rooms throughout the Hotel and the Tower, Defendants will provide at least one lavatory with a counter-top that is 34 inches above the finish floor surface...
-
Card Catalogs and Magazine Displays [8.4]
Requirements for fixed counters and tables [4.32] specify a surface height (34 inches maximum) and knee clearance below appropriate for extended use as a writing/work surface....
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
1011.2.4 Openings
Openings in the clear ground space surface shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1011.2.4 Openings. ...
-
1011.2.4 Openings
Openings in the clear ground space surface shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1011.2.4 Openings....
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
IMPLICATION OF A 19-INCH MINIMUM STANDARD FOR THE HIGHEST POINT IN THE LOWEST ADJUSTABLE POSITION
However, shorthand references to 19 inches as the minimum standard as used in this minority report should not be equated with a 19-inch transfer surface height, for two major reasons....
-
¼ Inch Minus Limestone
The surface was installed in two rolled and compacted 3 inch lifts....
-
Areas for further work
Areas for further work In the process of assisting the various organizations that represent surface materials and professional groups the following issues were identified as parameters...
-
Eunice Noell-Waggoner, IES, LC. Value, Contrast and Reflections
Reflective & Transparent Surfaces can be Dangerous Vertical Surfaces (slide 4) Two examples are shown of hazards from reflective and transparent vertical surfaces....
