B1. Is a relatively level (1:50 or 2% maximum slope in all directions) access aisle provided adjacent and parallel to the side of the vehicle pull-up area? [ADA Stds 4.6.6] Yes...
Search Results "Transfer Surface Height"
Filters
Commonly Searched Documents
-
B1. Slope
-
1016.7 Slopes
This section contains technical requirements for the maximum running slope and segment length (1016.7.1) and cross slope (1016.7.2) of outdoor recreation access routes.
-
Common Questions (Stairways)
Common Questions
-
Non-Circular Cross Section and Clearance (§505.5, §505.7)
Non-Circular Cross Section and Clearance (§505.5, §505.7)
-
Protocol B Heights Obtained
Again for the minimum height protocol HERL participants transferred lower on average than the NDVWSC participants....
-
I don’t want to discriminate against patients with disabilities, but I don’t want my staff to injure their backs by lifting people who use wheelchairs onto exam tables. If my nurse has a bad back, then she doesn’t have to help lift a patient, does she?
Q I don’t want to discriminate against patients with disabilities, but I don’t want my staff to injure their backs by lifting people who use wheelchairs onto exam tables. If my nurse...
-
Common Problems with Signs
Common Problems with Signs Ø Some signs – such as permanent room signs – are required to have Braille, high contrast, and raised lettering and must be located on the wall to...
-
I. BACKGROUND
I. BACKGROUND A. On November 25, 2003, Dennis Christopher Butler, Rosemary Ciotti, George Aguehounde, Marsha Johnson (the “Individual Plaintiffs”), and The Disability Rights...
-
A. Measuring Slope and Cross Slope
First, observe the general slope of the surface and place the builders' level on the pavement at the steepest point parallel to the direction of the slope....
-
11B-411.3.3.1 Height
The height of the reopening device shall comply with Section 11B-407.3.3.1....
-
11B-216.2 Designations
at the door to the space that they serve, but this is inferable from the fact that the requirement for Braille is contained within 11B-703.2, as are the requirements pertaining to the height...
-
Accessible Medical Equipment
Importance of Accessible Examination Tables, Chairs and Weight Scales http://www.hfcdihp.org/products Exam Room Selection for Accessible Examination Tables & Chairs PDF...
-
Adjustable height/gap protocol
One-hundred and sixteen (116) subjects were tested under this protocol, of which seven were unable to transfer with a height/gap combination in the configuration shown in (Figure 5). 86%...
-
Aquatic Recreation Facilities
The accessible means of entry can be either a pool lift, sloped entry, or transfer system....
-
Access Board: Informational and Directional Sign Requirements
This video is part of a longer animation produced by the U.S. Access Board. View the animation video in its entirety on the Access Board's website...
-
11B-203.9 Employee workstations
workstations shall only be required to comply with Sections 11B-207.1 _|Accessible Means of Egress; General|_, 11B-215.3 _|Fire Alarm Systems; Employee Work Areas|_, 11B-302 _|Floor or Ground Surfaces...
-
Identification [§216.5, §502.6]
ISA designations on the parking surface, even if required by a state or local government, cannot substitute for above-ground signs that remain visible at all times....
-
Bobrick 18" Straight Grab Bar Peened B-6806.99 x 18
18" (455mm) long, 1-1/2" (38mm) dia. tubing, peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick,...
-
Bobrick 18" Straight Grab Bar B-5806 x 18
18" (455mm) long, 1-1/4" (32mm) dia. tubing. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
-
Bobrick 18" Straight Grab Bar Peened B-5806.99 x 18
18" (455mm) long, 1-1/4" (32mm) dia. tubing , peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm)...
-
Bobrick 18" Straight Grab Bar B-6806 x 18
18" (455mm) long, 1-1/2" (38mm)dia. tubing. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
