[ADA Title III §36.104] Public entity means— (1) Any State or local government; (2) Any department, agency, special purpose district, or other instrumentality of a State or States...
Search Results "Enhanced 9-1-1"
Filters
Commonly Searched Documents
-
PUBLIC ENTITY
-
1007.2 Accessible Routes
EXCEPTIONS: 1. Playing surfaces shall not be required to comply with 302.2. 2....
-
Grab Bar Cross Sections
The proposed rule specified 1 ¼ to 1 ½ circular cross sections....
-
1018.1 General
EXCEPTIONS: 1....
-
QUESTION: WHEN DO THE REQUIREMENTS OF SECTION 37.42 BEGIN TO APPLY?
standard and other requirements of section 37.42(a) apply to stations that are approved for entry into final design or that begin construction or alteration of platforms on or after February 1,...
-
1018.1 General
EXCEPTIONS: 1....
-
11B-505.6 Gripping surface
Where provided, horizontal projections shall occur 1½ inches (38 mm) minimum below the bottom of the handrail gripping surface. Exceptions: 1. ...
-
Guest Rooms
to 25 1 0 1 26 to 50 2 0 2 51 to 75 3...
-
3104.2 Separate structures
Exceptions: 1. Buildings on the same lot in accordance with Section 503.1.2 shall be considered a single structure. 2. ...
-
404.2.5 Thresholds
Thresholds, if provided at doorways, shall be 1/2 inch (13 mm) high maximum. Raised thresholds and changes in level at doorways shall comply with 302 and 303....
-
404.2.5 Thresholds
Thresholds, if provided at doorways, shall be 1/2 inch (13 mm) high maximum. Raised thresholds and changes in level at doorways shall comply with 302 and 303....
-
410.6.3.1 PSTN (Section-by-Section Analysis)
with real-time two-way voice communication interoperates with the publicly switched telephone network (PSTN), real-time text conform to TIA 825-A (incorporated by reference in 508 Chapter 1...
-
4.10.9 Floor Plan of Elevator Cars
The clearance between the car platform sill and the edge of any hoistway landing shall be no greater than 1‒1/4 in (32 mm)....
-
4.10.9 FLOOR PLAN OF ELEVATOR CARS
The clearance between the car platform sill and the edge of any hoistway landing shall be no greater than 1-1/4 in (32 mm)....
-
11B-407.4.6.2.1 Size and shape
Buttons shall have square shoulders, be ¾ inch (19.1 mm) minimum in their smallest dimension and be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding surface...
-
11B-805.4 Examination, diagnostic and treatment rooms
of Statewide Health Planning and Development (OSHPD), which has jurisdiction over hospitals and long-term care facilities in California, issued Code Application Notice CAN 2-11B, dated 9/...
-
Bonded Impact/cushioning Surfaces
Figure 1. Overview of the test surfaces in Madison, Wisconsin....
-
Accessible Routes
The accessible route must comply with ADAAG provisions for the location, width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level...
-
505.1 General
Handrails are not required on walking surfaces with running slopes less than 1:20....
-
Top Landing [§406.4]
Side flare slopes cannot exceed 1:10 max. (or 1:12 max. in alterations where a top landing is unavailable)....
-
68.10. Definitions
(Effective June 1, 1994, 19 TexReg 3485; amended effective December 5, 1999, 24 TexReg 10855; amended effective June 26, 2000, 25 TexReg 6122; repealed effective November 5, 2001, 26 TexReg...
-
68.30. Exemptions
(Effective June 1, 1994, 19 TexReg 3485; amended effective May 6, 1998, 23 TexReg 4263; amended effective December 5, 1999, 24 TexReg 10855; amended effective June 26, 2000, 25 TexReg 6122...
-
68.53. Corrective Modifications Following Inspection
(New rule section effective November 5, 2001, 26 TexReg 8807; amended effective February 1, 2005, 30 TexReg 382; amended effective March 1, 2007, 32 TexReg 884) (a) When corrective modifications...