Buttons shall have square shoulders, be 3/4 inch (19.1 mm) minimum in the smallest dimension and shall be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding...
Search Results "Adult Dimension"
Filters
Commonly Searched Documents
-
11B-411.2.1.5.1 Size
-
Standard Roll-In Type Shower Compartments: ADA Standard Section 608.2.2
Section 608.2.2 covers the current ADA Standards for the size of standard roll-in type shower compartments.
-
E101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
-
C101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
-
Introduction
Dimension definitions and measurement techniques vary from study to study and, in many cases, samples were very small....
-
E101.3 Conventional Industry Tolerances (Section-by-Section Analysis)
E101.3 Conventional Industry Tolerances (Section-by-Section Analysis) This section would provide that dimensions are subject to conventional industry tolerances except where dimensions...
-
Transfer Space: ADA Standard Section 1008.3.1.3
The 48 inch (1220 mm) long minimum dimension of the transfer space shall be centered on and parallel to the 24 inch (610 mm) long minimum side of the transfer platform....
-
Alternate Roll-In Type Shower Compartments: ADA Standard Section 608.2.3
Section 608.2.3 covers the current ADA Standards for the size and clearances of alternate roll-in type shower compartments.
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
11B-604.9 Water closets and toilet compartments for children's use
When the exception in Section 11B-604.1 is used, the suggested dimensions of Table 11B-604.9 for a single age group shall be applied consistently to the installation of a water closet and...
-
Children and Adults with Attention-Deficit/Hyperactivity Disorder (CHADD)
CHADD is a membership organization, produces the bi-monthly Attention magazine (for members), and sponsors an annual conference. The National Resource Center on ADHD (NRC) is the...
-
General Tips for Communicating with People with Disabilities
Treat adults as adults. Address people who have disabilities by their first names only when extending the same familiarity to all others. Relax....
-
Calculation of Percentages: ADA Standard Section 104.2
Section 104.2 of the ADA Standards covers the most current information on the calculation of percentages in the ADA Standards.
-
11B-104.2 Calculation of percentages
Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half shall be permitted....
-
3. MINIMUMS, MAXIMUMS AND SPECIFYING AT THE LIMIT
MINIMUMS, MAXIMUMS AND SPECIFYING AT THE LIMIT: Where an element is to be installed at the minimum or maximum permitted dimension, such as "48 inches maximum", it is not good practice to...
-
Cross Section of Gripping Surfaces
The 2004 ADA and ABA Accessibility Guidelines specify the following dimensions for grab bars to enable individuals with disabilities to firmly grasp the grab bars and support themselves...
-
C101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range with specific minimum or maximum end points....
-
E101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range with specific minimum or maximum end points....
-
Conventions [§104]
Conventions [§104] Most dimensions in the ADA Standards are specified as a minimum, maximum, or as a range. In a few areas, absolute dimensions are specified....
-
Overall
They liked the topography and they thought children and adults could enjoy it equally....
-
11B-1008.3.1.3 Transfer space
The 48 inch (1219 mm) long minimum dimension of the transfer space shall be centered on and parallel to the 24 inch (610 mm) long minimum side of the transfer platform....
-
What would happen with other disability groups?
Therefore, we would hypothesize that our results would also be similar if we had tested other disability populations or older adults....
-
C101.3 Conventional Industry Tolerances (Section-by-Section Analysis)
C101.3 Conventional Industry Tolerances (Section-by-Section Analysis) This proposed section, which has a parallel provision in the proposed 508 Standards (E101.3), would provide that dimensions...
-
2010 ADA Standards
It is good practice when specifying dimensions to avoid specifying a tolerance where dimensions are absolute....
