., Amtrak and a commuter railroad) and that, in many cases, the floor heights of the various railroads' equipment are different....
Search Results "Grab Bar Height"
Commonly Searched Documents
-
Comments
-
Side reach (Section-by-Section Analysis)
The 1991 Standards at section 4.2.6 establish a maximum side-reach height of 54 inches. The 2010 Standards at section 308.3.1 reduce that maximum height to 48 inches....
-
Side reach (Section-by-Section Analysis)
The 1991 Standards at section 4.2.6 establish a maximum side-reach height of 54 inches. The 2010 Standards at section 308.3 reduce that maximum height to 48 inches....
-
II-7.3100 General
Are any additional dialing or space bar requirements permissible for 911 systems? No. Additional dialing or space bar requirements are not permitted....
-
Carpet: ADA Standard Section 302.2
Section 302.2 covers the current ADA Standards for carpet.
-
11B-505.10.3 Bottom extension at stairs
The horizontal extension of a handrail shall be 12 inches (305 mm) long minimum and a height equal to that of the sloping portion of the handrail as measured above the stair nosings....
-
11B-504.8 Floor identification
11B-703.3 and 11B-703.5 shall be located at the landing of each floor level, placed adjacent to the door on the latch side, in all enclosed stairways in buildings two or more stories in height...
- American Specialties Double Robe Hook 7345
-
907.2.4 Group F
A manual fire alarm system shall be installed in Group F occupancies that are two or more stories in height and have an occupant load of 500 or more above or below the lowest level of exit...
-
1008.1.9.7, Item 5
THIS DOOR WILL OPEN IN 15 [30] SECONDS ALARM WILL SOUND” Sign lettering shall be at least 1 inch (25 mm) in height and shall have a stroke of not less than 1/8 inch (3.2 mm)....
-
Question 17
Should the standards be different for adjustable beds, such as hospital beds, and for fixed height beds?...
-
Triax 2000
A large tripod that can be raised to a fall height above the highest play surface on a playground. ...
-
§ 37.3 Alteration
rehabilitation, reconstruction, historic restoration, changes or rearrangement in structural parts or elements, and changes or rearrangement in the plan configuration of walls and full-height...
-
What kinds of treatments constitute maintenance rather than an alteration?
considered maintenance are: painting or striping lanes, crack filling and sealing, surface sealing, chip seals, slurry seals, fog seals, scrub sealing, joint crack seals, joint repairs, dowel bar...
-
B. The Release Includes State and Local Law Claims Which Are Not Addressed By The Agreements
The Release Includes State and Local Law Claims Which Are Not Addressed By The Agreements The Agreements are also overbroad in that they bar class members from bringing claims under state...
-
Clear Width [4.13.5] and Vertical Clearance
Panic bars and other hardware do not require additional width since they are usually mounted above the widest portion of wheelchairs....
- Symmetry Vertical Platform Lift VPC-SL
-
FAQ: How do I browse and search content?
Use the search function The search bar is present on each page of Corada. ...
-
11B-306.3.4 Clearance reduction
inches (229 mm) and 27 inches (686 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (152 mm) in height...
-
Dressing, Fitting, or Locker Rooms
Operating mechanisms provided on accessible lockers must also meet ADAAG provisions for their operation and height....
-
I. Introduction
The purpose of this Minority Report is to make a formal recommendation for a minimum transfer surface low height of 19 inches for diagnostic imaging medical equipment....
-
CONCLUSION
In addition, it will build on the growing percentage of providers voluntarily purchasing accessible, adjustable height tables....
-
R308.1.2.1 Platform and Vehicle Floor Coordination
The Department of Transportation regulations (49 CFR parts 37 and 38) require the height of the vehicle floor and the station platform to be coordinated so as to minimize the vertical and...
-
T703.1 General
The symbol shall have a background field height of 4 inches (100 mm) minimum. The symbol and its background shall have a non-glare finish....