Some commenters also recommended a higher minimum height of 29 inches instead of 28 inches to allow a more comfortable knee clearance. Response....
Search Results "Latch Side Clearance"
-
Table Surface Height
-
Accessible Route Into and Through the Business
Customers with disabilities will not be able to shop in a store if the route through an entry plaza is too narrow because of a display of snow blowers, if the maneuvering clearance alongside...
-
Smith Carrel Hi-Lo Study Carrel - "The Original"
Side panels are arched both top (convex) and bottom (concave) for aesthetic appeal....
-
R406 Reach Ranges (Section-by-Section Analysis)
R406 Reach Ranges (Section-by-Section Analysis) Forward and side reach ranges must be between 380 millimeters (1.25 feet) and 1220 millimeters (4 feet) above the finish surface....
-
11B-502.6.4.1
The centerline of the International Symbol of Accessibility shall be a maximum of 6 inches (152 mm) from the centerline of the parking space, its sides parallel to the length of the parking...
-
11B-502.6.4.1
The centerline of the International Symbol of Accessibility shall be a maximum of 6 inches (152 mm) from the centerline of the parking space, its sides parallel to the length of the parking...
-
11B-410.7 Landing size
ETA Editor's Note There are no requirements for landing size in 2010 ADA Standards, although the door maneuvering clearance requirements at 404.2.4 should be applicable outside the platform...
-
Sargent 8900 Mortise Lock Exit Device
line of exit devices that provide the best combination of simplicity, strength, durability, aesthetics and innovation. 8900 Mortise Lock Exit Device has concealed single point guarded latching...
-
Hager Companies Rectangular Wrought Door Pull 2
Rectangular Wrought Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2" (64 mm) Clearance available on special order....
-
R305.2.5 Pedestrian At-Grade Rail Crossings
At pedestrian at-grade rail crossings not located within a street or highway, detectable warning surfaces shall be placed on each side of the rail crossing....
-
Surface and Size [§305.2 and §305.3]
The minimum size (30” by 48”) applies whether the space is positioned for forward or side approaches....
-
11B-502.6.4.1
The centerline of the International Symbol of Accessibility shall be a maximum of 6 inches (152 mm) from the centerline of the parking space, its sides parallel to the length of the parking...
-
Paperwork Reduction Act
This rule does not contain any paperwork or record keeping requirements, and does not require clearance under the PRA....
-
11B-604.8.1.1.1 Maneuvering space with in-swinging door
In a wheelchair accessible compartment with an in-swinging door, a minimum 60 inches (1524 mm) wide by 36 inches (914 mm) deep maneuvering space shall be provided in front of the clearance...
-
Paperwork Reduction Act
This rule does not contain any paperwork or record keeping requirements and does not require clearance under the PRA....
-
11B-604.8.1.1.1 Maneuvering space with in-swinging door
In a wheelchair accessible compartment with an in-swinging door, a minimum 60 inches (1524 mm) wide by 36 inches (914 mm) deep maneuvering space shall be provided in front of the clearance...
-
604.5.2 Rear Wall
The rear wall grab bar shall be 36 inches (915 mm) long minimum and extend from the centerline of the water closet 12 inches (305 mm) minimum on one side and 24 inches (610 mm) minimum on...
-
Parking Spaces [4.6.3]
For vans with side-mounted lifts, a combined width of almost 17 feet is often needed for the deployment and use of side-mounted lifts; ADAAG requires at least 16 feet....
-
Hager Companies Modified Half Round Wrought Door Pull 1
Modified Half Round Wrought Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2" (64 mm) Clearance available on special order....
-
11B-608.5.3 Alternate roll-in type shower compartments
In alternate roll-in type shower compartments, operable parts of controls and faucets shall be installed on the side wall of the compartment adjacent to the seat wall 19 inches (483 mm)...
-
11B-608.5.3 Alternate roll-in type shower compartments
In alternate roll-in type shower compartments, operable parts of controls and faucets shall be installed on the side wall of the compartment adjacent to the seat wall 19 inches (483 mm)...
-
Ramps M303:3.3, 3.3.1, 3.3.2
Ramps with drop offs ½ inch or greater would be required to provide edge protection 2 inches high minimum on each side to prevent users from inadvertently travelling off the sides of the...
-
308 Reach Ranges
In the final rule, the maximum side reach has been lowered to the height specified for forward reaches....
-
11B-809.10.7.1 Floor space
The floor space at water closets shall be 48 inches (1219 mm) wide minimum measured perpendicular to the side wall....
