In locations where toilets are adjacent to walls or bathtubs, the center line of the fixture is a minimum of 1'6" from the obstacle....
Search Results "Assisted Living Center"
Commonly Searched Documents
-
7(2)(b)(iv)
-
11B-503.3.3 Marking
The area within the borderlines shall be marked with hatched lines a maximum of 36 inches (914 mm) on center in a color contrasting with that of the aisle surface....
-
12183(b) Elevator
be construed to require the installation of an elevator for facilities that are less than three stories or have less than 3,000 square feet per story unless the building is a shopping center...
-
1134A.8, Item 4.3
The knee and toe space shall be centered on the fixture, and shall comply with Section 1138A.2....
-
A4.13.9 Door Hardware
To be effective, they should cover the door width, less approximately 2 in (51 mm), up to a height of 16 in (405 mm) from its bottom edge and be centered across the width of the door....
-
Side Approach
Recommendation: The clear floor space should be centered on the ATM unit....
-
1134A.8, Item 4.3
The knee and toe space shall be centered on the fixture, and shall comply with Section 1138A.2....
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
11B-809.2.2 Turning space
For example, in kitchens, Section 11B-804.3.1 requires at least one work surface with clear floor space complying with Section 11B-306 to be centered beneath....
-
§ 37.165(f)
(f) Where necessary or upon request, the entity's personnel shall assist individuals with disabilities with the use of securement systems, ramps and lifts....
- The Spa Lift Elite™ Pool & Spa Access Lift
-
1003.2.13.5.4 Instructions
Persons able to use the exit stairway do so as soon as possible, unless they are assisting others. 3....
-
§ 37.201(a)
The operator shall ensure that assistance is provided to passengers with disabilities as needed to enable the passenger to get on and off the bus at the stop (e.g., operate the lift and...
-
5.2.1.2 Transfer Surface Depth Recommendation for M301
Edward Steinfeld, Director of the Center of Inclusive Design and Environmental Access at the University of Buffalo, reported that his research data suggested that a depth of 15 inches would...
-
Data Analysis
Areas centered around the transfer station were defined and the percentage of the study participants who were able to transfer in that area were calculated....
-
1.1.14 Flatness of ramp cross slope
For ramps up to and including 5 ft (1525 mm) wide between the handrails, measure cross slope in the center of the ramp. See Fig. 6(a)....
-
11B-608.2.1 Transfer type shower compartments
Transfer type shower compartments shall be 36 inches (914 mm) by 36 inches (914 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (914...
-
§ 38.29(b)
starting to board, and to continue using such assists throughout the boarding and fare collection process....
- Damixa Clover Easy Kitchen Mixer with X-Change Connector Kit 60027
-
§104.2 Application.
This part applies to each recipient of Federal financial assistance from the Department of Education and to the program or activity that receives such assistance....
-
§104.6(a)(1)
(1) If the Assistant Secretary finds that a recipient has discriminated against persons on the basis of handicap in violation of section 504 or this part, the recipient shall take such remedial...
- IRS Videos in ASL IRS Tips: For Deaf Users of Relay Services (Captions & Audio)
-
1009.5.2 Transfer Space
transfer space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer platform surface and shall be centered...
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....