Machinery Spaces (§203.5) Spaces used only by service personnel for maintenance, repair, or occasional monitoring of equipment Examples: elevator pits/ penthouses, mechanical/...
Search Results "Centered Clear Floor Space"
-
Machinery Spaces (§203.5)
-
12162(a)(3)(A)(ii) a number of spaces
(ii) a number of spaces...
-
§ 38.83(b)(7) Platform gaps
When the lift is at vehicle floor height with the inner barrier (if applicable) down or retracted, gaps between the forward lift platform edge and vehicle floor shall not exceed 1/2 inch...
-
Maneuvering Space at Doors
Other commenters stated that the maneuvering space was necessary to ensure safe egress in cases of emergency. Response....
-
Handrails
The clear width between handrails must be between 33 and 38 inches. The handrail height must be between 34 and 38 inches to the top of the gripping surface....
-
11B-604.8.1.2 Doors
Doors shall not swing into the clear floor space or clearance required for any fixture....
-
11B-604.8.1.2 Doors
Doors shall not swing into the clear floor space or clearance required for any fixture....
-
12.1 Q...How is the individual building test performed for additional stories, to determine if those stories must also be treated as ground floors?
For purposes of determining whether a non-elevator building has more than one ground floor, the point of measurement for additional ground floors, after the first ground floor has been established...
-
§ 38.153(a)
(a) Floor surfaces on aisles, step treads and areas where wheelchair and mobility aid users are to be accommodated shall be slip-resistant....
-
§ 38.117(a)
(a) Floor surfaces on aisles, step treads and areas where wheelchair and mobility aid users are to be accommodated shall be slip-resistant....
-
2.1 Q. If a building includes three residential dwelling units and one or more commercial spaces, is the building a covered multifamily dwelling under the Fair Housing Act?
Covered multifamily dwellings are buildings consisting of four or more dwelling units, if such buildings have one or more elevators; and ground floor dwelling units in other buildings consisting...
-
11B-812.7.2 Marking
Access aisles at vehicle spaces shall be marked with a painted borderline around their perimeter....
-
11B-304 TURNING SPACE
[See subsections ...]
-
11B-304 Turning space.
[See subsections ...]
-
11B-304 Turning space
[See subsections ...]
-
410.6 Doors and Gates
End doors and gates shall provide a clear width 32 inches (815 mm) minimum. Side doors and gates shall provide a clear width 42 inches (1065 mm) minimum....
-
503.2 Vehicle Pull-Up Space
Passenger loading zones shall provide a vehicular pull-up space 96 inches (2440 mm) wide minimum and 20 feet (6100 mm) long minimum....
-
406.4 Landings
The landing clear length shall be 36 inches (915 mm) minimum. The landing clear width shall be at least as wide as the curb ramp, excluding flared sides, leading to the landing....
-
T210.1 General
Non-rail vehicles shall provide wheelchair spaces in accordance with T210....
-
General: ADA Standard Section 226.1
Section 226.1 of the ADA Standards covers information in the current ADA Standards on scoping requirements for dining surfaces and work surfaces.
-
The Rehabilitation Engineering Research Center on Recreational Technologies (RERC Rec-Tech)
The Rehabilitation Engineering Research Center on Recreational Technologies (RERC Rec-Tech) at University of Alabama-Birmingham is a five-year grant funded by the National Institute on Disability...
-
11B-410.6 Doors and gates
End doors and gates shall provide a clear width 32 inches (813 mm) minimum. Side doors and gates shall provide a clear width 42 inches (1067 mm) minimum....
-
11B-410.6 Doors and gates
End doors and gates shall provide a clear width 32 inches (813 mm) minimum. Side doors and gates shall provide a clear width 42 inches (1067 mm) minimum....
-
503.2 Vehicle Pull-Up Space
Passenger loading zones shall provide a vehicular pull-up space 96 inches (2440 mm) wide minimum and 20 feet (6100 mm) long minimum. [ECTCR UFAS 4.6.5]...
