plane perpendicular to the edge of the unobstructed clear floor space at the farthest protrusion of the automated teller machine or surround is not more than 10 in (255 mm), the maximum height...
Search Results "Table Height"
-
4.34.3(2)(a) Reach Depth Not More Than 10 in
-
A4.13.9 DOOR HARDWARE
To be effective, they should cover the door width, less approximately 2 in (51 mm), up to a height of 16 in (405 mm) form its bottom edge and be centered across the top....
-
11B-306.3.4 Clearance reduction
inches (229 mm) and 27 inches (686 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (152 mm) in height...
-
1132A.1 Primary entry doors and required exit doors
The width and height of primary entry doors and all required exit doors shall comply with Section 1126A.1....
-
§ 38.95(b)(7) Platform gaps
When the lift is at car floor height with the inner barrier down (if applicable) or retracted, gaps between the forward lift platform edge and car floor shall not exceed 1/2 inch horizontally...
-
§ 38.125(b)(7) Platform gaps
When the lift is at car floor height with the inner barrier (if applicable) down or retracted, gaps between the forward lift platform edge and car floor shall not exceed 1/2 inch horizontally...
-
11B-306.3.4 Clearance reduction
inches (229 mm) and 27 inches (686 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (152 mm) in height...
-
1132A.1 Primary entry doors and required exit doors
The width and height of primary entry doors and all required exit doors shall comply with Section 1126A.1....
-
Speed
Table 12. Speed....
-
D. Department of Justice Activities Related to Health Care Providers and Medical Equipment
., examination tables and chairs, mammography equipment, weight scales); patient lifts and other methods for transferring individuals from their mobility devices to medical equipment; and...
-
1125B.3
SECTION 1125B - STORAGE 1125B.3 Height. Accessible storage spaces shall be within at least one of the reach ranges specified in Sections 1118B.5 and 1118B.6....
-
Notes
Notes GG Analysis of Seat Heights for Wheeled Mobility Devices. The study is available at http://udeworld.com/analysis-of-seat-height-for-wheeled-mobility-devices....
-
Medical Diagnostic Equipment Accessibility Standards Sub Committee Recommendations Stretcher Final Report
Features Addressed in Technical Criteria Types Of Equipment To Which Technical Criteria Applies Supine, prone, or side-lying position (M301) Transfer surface, including height...
-
1134A.5, Item 2
The grab bar reinforcement shall be a minimum of 6 inches (152.4 mm) nominal in height. (See Figure 11A-9G)....
-
1016.5 Obstacles
This section requires obstacles to not exceed 1/2 inch in height measured vertically to the highest point....
-
1134A.5, Item 2
The grab bar reinforcement shall be a minimum of 6 inches (152.4 mm) nominal in height. (See Figure 11A-9G)....
-
ALTERATION
resurfacing of circulation paths or vehicular ways, changes or rearrangement of the structural parts or elements, and changes or rearrangement in the plan configuration of walls and full-height...
-
Elements Within Camping Units With Mobility Features [F244.2.3]
., picnic tables, tent pads) is provided within a camping unit with mobility features, at least two of the same type of element must comply with the applicable technical requirements for...
-
9.1.3 Sleeping Accommodations for Persons with Hearing Impairments
rooms and suites required by 9.1.2, sleeping rooms and suites that comply with 9.3 (Visual Alarms, Notification Devices, and Telephones) shall be provided in conformance with the following table...
-
1018.7.1 Maximum Running Slope and Segment Length
Where the running slope of a segment a beach access route is steeper than 1:20 (5%), the maximum length of the segment is specified in Table 1018.7.1, and a resting interval is required...
-
Disability In the Context of Diversity
Department of Labor employees bring their diverse perspectives to the conference table. — U.S. Department of Labor...
-
Jean Tessmer
Some of us prefer to mount to allow 28" knee clearance minimum to give the person in the wheelchair a lower shelf height of 32" depending on the thickness of your new #200 baby changer shelf...
-
11B-240.2.1.2 Additional number and types
Where elevated play components are provided, ground level play components shall be provided in accordance with Table 11B-240.2.1.2 and shall comply with Section 11B-1008.4....
-
F240.2.1.2 Additional Number and Types
Where elevated play components are provided, ground level play components shall be provided in accordance with Table F240.2.1.2 and shall comply with 1008.4....