Product Features Fabricated of a heavy die cast aluminum with baked white enamel finish Hands free electric sensor provides easy operation Features a powerful 3450 RPM...
Search Results "Abrasive Surface"
-
AJW Architectural Products U1525EA Series Automatic 120 Volt Hand Dryer, White Powder Coat - Surface Mounted
-
AJW Architectural Products U815 Dual Toilet Tissue Dispenser w/ Mounted Shelf - Surface Mounted - Non-Controlled
Product Features Fabricated of #18 gauge stainless steel with #4 satin finish. Holds one or two standard toilet tissue rolls. Product Specs Shelf: Fabricated of #18 gauge...
-
AJW Architectural Products U590 1.6 Gallon Sanitary Napkin Disposal w/ Keyed Access Panel - Surface Mounted
Product Features Fabricated of #22 gauge stainless steel with a #4 satin finish Waste receptacle has a 1.5 gallon capacity Bottom panel is hinged for easy removal of...
-
AJW Architectural Products UJ11 Series UJ11A Coat Hook Strip 24"L, 3 Hooks - Surface Mounted
Product Features Fabricated of #18 gauge stainless steel with #4 satin finish Units with greater widths require additional hooks Custom lengths available Product...
-
11B-307.3.1 Edges and corners
Where signs or other objects are mounted on posts or pylons, and their bottom edges are less than 80 inches (2032 mm) above the floor or ground surface, the edges of such signs and objects...
-
11B-307.3.1 Edges and corners
Where signs or other objects are mounted on posts or pylons, and their bottom edges are less than 80 inches (2032 mm) above the floor or ground surface, the edges of such signs and objects...
-
Dome Spacing: ADA Standard Section 705.1.2
Truncated domes in a detectable warning surface shall have a center-to-center spacing of 1.6 inches (41 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
-
Check-out Aisle Counter Height
The counter surface of check-out aisle counters is required to be 38 inches high maximum. Comments from persons with disabilities considered 38 inches to be too high. Response....
-
Accessible Mats for Beach and Outdoor Events
While progress has been made over the years, many beaches, parks, and other public areas still do not provide accessible routes and those who do may not have firm and stable surfaces....
-
Delimitations
following: Data from this study were obtained from a longitudinal study administered through the National Center on Accessibility (NCA) at Indiana University; One category of surface...
-
APPENDIX B
OUTSIDE SURFACES Figure 27: Pictures and Roughness Index of Outside surfaces...
-
Recommendations for Further Action
are available for use on pedestrian trails and how various surface materials perform in different regions of the country....
-
References
Advisory 304.2 Floor or Ground Surface Exception....
-
406.2 Counter Slope
Counter slopes of adjoining gutters and road surfaces immediately adjacent to the curb ramp shall not be steeper than 1:20....
-
Tactile Symbols: ADA Standard Section 707.6.3.2
Function key surfaces shall have tactile symbols as follows: Enter or Proceed key: raised circle; Clear or Correct key: raised left arrow; Cancel key: raised letter ex; Add Value key: raised...
-
11B-707.6.3.2 Tactile symbols
Function key surfaces shall have tactile symbols as follows: Enter or Proceed key: raised circle; Clear or Correct key: raised left arrow; Cancel key: raised letter ex; Add Value key: raised...
-
11B-707.6.3.2 Tactile symbols
Function key surfaces shall have tactile symbols as follows: Enter or Proceed key: raised circle; Clear or Correct key: raised left arrow; Cancel key: raised letter ex; Add Value key: raised...
-
Dome Size: ADA Standard Section 705.1.1
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (23 mm) minimum and 1.4 inches (36 mm) maximum, a top diameter of 50 percent of the base diameter minimum...
-
11B-813.2.1.3 Height and operation
Adult changing table height shall be adjustable from 17 inches (432 mm) above the floor or ground to 38 inches (965 mm) above the floor or ground, as measured to the top of the changing surface...
-
11B-411.2.1.5.1 Size
Buttons shall have square shoulders, be 3/4 inch (19.1 mm) minimum in the smallest dimension and shall be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding surface...
-
11B-813.2.1.3 Height and operation
Adult changing table height shall be adjustable from 17 inches (432 mm) above the floor or ground to 38 inches (965 mm) above the floor or ground, as measured to the top of the changing surface...
-
11B-411.2.1.5.1 Size
Buttons shall have square shoulders, be 3/4 inch (19.1 mm) minimum in the smallest dimension and shall be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding surface...
-
[2010 ADAS] 105.2.3 ASTM
ASTM F 1292-99 and ASTM F 1292-04 establish a uniform means to measure and compare characteristics of surfacing materials to determine whether materials provide a safe surface under and...
-
707.6.3.1 Contrast
Function keys shall contrast visually from background surfaces. Characters and symbols on key surfaces shall contrast visually from key surfaces....
