Benches must be strong enough to withstand a vertical or horizontal force of 250 pounds applied at any point on the seat, fastener, mounting device, or supporting structure....
Search Results "Vertical Clearance"
-
Benches
-
Model Building Codes and Industry Standards
For example, unlike the ADA guidelines, the ANSI standards require an additional vertical grab bar at water closets, transfer shower stalls, and tubs....
-
§ 38.175(a)
Vertical alignment may be accomplished by car air suspension or other suitable means of meeting the requirement....
-
810.5.3 Platform and Vehicle Floor Coordination
The height and position of a platform must be coordinated with the floor of the vehicles it serves to minimize the vertical and horizontal gaps, in accordance with the ADA Accessibility...
-
1118B.3
Changes in level up to 1/4 inch (6.4 mm) may be vertical and without edge treatment [see Figure 11B-5E(c)]....
-
Mammography Equipment
2.It is best to position equipment to allow both front and side approaches; for some patients a side or angled approach may be better for positioning at the camera unit and plate. 3.Clearance...
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
Accessible Restrooms, Fitting Rooms, and Elevators
Remove trash receptacles and cigarette urns from under elevator hall call buttons and beside doors to ensure access to controls and sufficient maneuvering clearance....
-
Rough Grade Site Inspection
surface requirements along accessible routes, accessible parking and access aisles, etc. 11B-403 Verify if under-slab plumbing will provide adequate clearances...
-
Protruding Objects on Beach Access Routes
Provide and maintain clearance from natural elements around beach access routes in accordance with your unit's standards; keep in mind overhanging hazards to people who are blind or have...
-
Rough Grade Site Inspection
surface requirements along accessible routes, accessible parking and access aisles, etc. 11B-403 Verify if under-slab plumbing will provide adequate clearances...
-
Handrails Along Walking Surfaces [§403.6, §505]
Surface requirements and clearances facilitate a power grip along the length of handrails. Handrails can have circular or non-circular cross-sections, but must have rounded edges....
-
M301 Diagnostic Equipment Used by Patients in Supine, Prone, or Side-Lying Position; M302 Diagnostic Equipment Used by Patients in Seated Position
The sections also include provisions for clearance in and around the base of the equipment for lift compatibility to allow the use of a patient lift by patients with disabilities for whom...
-
Work Areas [4.1.1(3)]
Recommendations: Space for turning within the work area and interior maneuvering clearances at doors, while not required, should be considered, especially where entrapment may be a concern...
- Pilot Rock AFT Series - End Accessible Traditional A-Frame Picnic Table - Using Recycled Plastic
- Pilot Rock AFT Series - End Accessible Traditional A-Frame Picnic Table - Using Lumber
- Kohler® Mazz Single-Handle Pull-Down Sprayer Kitchen Faucet in Vibrant Stainless
- Harmar IL500 Sierra Incline Platform Lift
-
11B-805 Medical care and long-term care facilities
Touch screen units shall be allowed to be vertically mounted with the centerline of the display screen no more than 52 inches above the floor in compliance with Section 11B-707.7.1.1....
-
Resting Intervals [1016.8]
The vertical alignment of the ORAR, turning space, and resting interval must be nominally planar (i.e., as flat as possible) so that all the wheels of a mobility device touch the ground...
-
Dune Crossings [1018.10]
The technical requirements for dune crossings do not address the vertical pickets provided in some handrail designs....
-
1. Typical Issues for Individuals Who Use Wheelchairs, Scooters, or other Mobility Devices
Ramps with a vertical rise of more than 6 inches must have handrails on both sides....
-
Transit Stops (R308.1) (Section-by-Section Analysis)
Boarding platforms at transit stops must be positioned to coordinate with vehicles to minimize the vertical and horizontal gaps....
-
1010.1.7 Thresholds
Raised thresholds and floor level changes greater than ¼ inch (6.4 mm) at doorways shall be beveled with a slope not greater than one unit vertical in two units horizontal (50-percent slope...