A portion of the counter surface that is 36 inches (915 mm) long minimum and 36 inches (915 mm) high maximum above the finish floor shall be provided....
Search Results "Surface Material"
-
Parallel Approach: ADA Standard Section 904.4.1
-
23.1 Q. What type of reinforcement should be used to reinforce bathroom walls for the later installation of grab bars?
The Guidelines do not prescribe the type of material to use or method of providing reinforcement for bathroom walls....
-
§ 38.159(b)(1) Design load
pulleys, and shafts, which can be expected to wear, and upon which the lift depends for support of the load, shall have a safety factor of at least six, based on the ultimate strength of the material...
-
11B-903.6 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
-
§ 37.139(e)(1)(i)
(i) The availability of information about the process and application materials in accessible formats;...
-
FAQ: Why should I enter ADA references in my Voices post?
When you enter relevant ADA references in your Voices post, the post is integrated with Corada’s existing database of other accessibility-related material, so your question, comment, Opinion...
-
II. LEGAL STANDARD
Summary judgment is only appropriate where the “materials in the record, including depositions, documents, electronically stored information, affidavits or declarations, stipulations (including...
-
11B-406.5.6 Grade breaks
Grade breaks shall not be permitted on the surface of ramp runs and turning spaces. Surface slopes that meet at grade breaks shall be flush....
-
Story
That portion of a building or facility designed for human occupancy included between the upper surface of a floor and upper surface of the floor or roof next above....
-
11B-406.5.6 Grade breaks
Grade breaks shall not be permitted on the surface of ramp runs and turning spaces. Surface slopes that meet at grade breaks shall be flush....
-
ADA Standards for Accessible Design Pocket Guide: ADA Standard Section 2010
The complete guide to the 2010 ADA Standards for Accessible Design with notes provided by national accessibility experts Evan Terry Associates
-
11B-703.4.1 Height above finish floor or ground
Tactile characters on signs shall be located 48 inches (1219 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest Braille cells and 60 inches (1524...
-
11B-703.4.1 Height above finish floor or ground
Tactile characters on signs shall be located 48 inches (1219 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest Braille cells and 60 inches (1524...
-
Bradley MG Terreon Waste Receptacle
Compatible with Express Lavatory Systems - MG-Series Cover is constructed of vandal-resistant Terreon or TerreonRE Solid Surface Material, available in dozens of colors...
-
Sec.36.603(c)
(c) The submitting official shall include the following materials and information in support of the request:...
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
Polling place violations that can be remediated with temporary measures
Henderson Elementary School, 1800 Dismuke Street, Houston, TX Parking: The surface slope in the designated accessible parking space is not level in all directions and exceeds the...
-
1010.1.4 Floor elevation
Variations in elevation due to differences in finish materials, but not more than ½ in (12.7 mm)....
-
1010.1.4 Floor elevation
Variations in elevation due to differences in finish materials, but not more than ½ in (12.7 mm)....
-
M101.6 Dimensional Tolerances
Dimensions are subject to conventional industry tolerances for manufacturing processes, material properties, and field conditions....
-
M101.5 Dimensional Tolerances
Dimensions are subject to conventional industry tolerances for manufacturing processes, material properties, and field conditions...
-
11B-904.3.2 Counter
The counter surface height shall be 38 inches (965 mm) maximum above the finish floor or ground....
-
Counter: ADA Standard Section 904.3.2
The counter surface height shall be 38 inches (965 mm) maximum above the finish floor or ground....
