1 1/2" offset sink assemble with 151A stainless steel basket strainer.
Search Results "Floor Surface"
-
McGuire Manufacturing Co., Inc. PW1151AWC: 1 1/2" Offset Sink 151A Stainless Steel Strainer
-
McGuire Manufacturing Co., Inc. PW1149WC: 1 1/2" Offset Sink 149 Flat Strainer
1 1/2" offset sink assemble with 149 brass flat grid strainer.
-
Zurn Industries Rigid Lavatory Enclosure - Vandal Gard
Rigid plastic lavatory enclosure 20" by 18" Conceals all piping, heaters, and other equipment below sink. 3-year warranty
-
McGuire Manufacturing Co., Inc. 155WC: Offset Lavatory Strainer
Furnished with heavy cast brass grid drain strainer, elbow and 1 1/4" 17GA seamless tubular offset tailpiece. ADA compliant. 8 3/4" x 5 1/8" OD.
-
McGuire Manufacturing Co., Inc. ProDrainWC: Lavatory Strainer Less Overflow
Offset strainer less overflow. Furnished with heavy brass grid drain strainer, heavy brass elbow and 1 1/4" 17GA seamless tubular brass offset tailpiece.
-
McGuire Manufacturing Co., Inc. 1151WC: Offset Strainer with 151 Basket Strainer
Offset sink strainer with chrome plated forged brass basket strainer with brass basket. 2 1/8" x 4 1/2" OD.
-
IPS Corporation Truebro® Lav Shield® Protective Lavatory Enclosure
Lav Shield® provides ADA-compliant undersink protection and meets requirements for wheelchair accessibility. Durable, single-piece construction conceals piping, electronic faucet...
-
McGuire Manufacturing Co., Inc. PW1000WC: 1 1/2" Offset Sink
1 1/2" offset sink assembly prewrapped.
-
McGuire Manufacturing Co., Inc. 1000WC: Offset Strainer - Offset Only
Offset sink strainer wheelchair offset. Allows up to 11" offset for wheelchair access use of most ADA sinks. The offset fits most 1 1/2" direct connect sink strainers including all...
-
McGuire Manufacturing Co., Inc. 1152WC: Offset with 152 Wide Top Strainer
Offset sink strainer with chrome plated wrought brass 4 1/2" wide top sink strainer. 1 3/4" x 4 1/2" OD.
-
McGuire Manufacturing Co., Inc. Heavy Finish Offset Lavatory Strainer
Classic McGuire wheelchair lavatory strainer. Furnished with heavy cast brass grid drain strainer, elbow and 1 1/4" 17GA seamless tubular offset tailpiece. PVD chrome finish. ADA...
-
§ 38.127(c)
., heating and air conditioning controls, lighting controls, call buttons, electrical outlets, etc.) shall be mounted no more than 48 inches, and no less than 15 inches, above the floor...
-
1.2 Q. Does the Fair Housing Act cover four one-story dwelling units that share common walls and have individual entrances?
The Fair Housing Act applies to all units in buildings consisting of four or more dwelling units if such buildings have one or more elevators; and ground floor dwelling units in other buildings...
-
M305.3.1.1 Horizontal Position
The length of gripping surfaces on horizontal standing supports shall be 4 inches (100 mm) minimum except for diagnostic equipment containing a wheelchair space which shall comply with M305.3.1.2...
-
M305.3.2.2 Vertical Position
The height of the lowest end of the gripping surface on vertical standing supports shall be 34 inches (865 mm) minimum and 37 inches (940 mm) maximum above the standing surface....
-
§ 38.23(c)(8) Handrails
them from outside the vehicle while starting to board, and to continue to use them throughout the boarding process, and shall have the top between 30 inches and 38 inches above the ramp surface...
-
2.1 Q. If a building includes three residential dwelling units and one or more commercial spaces, is the building a covered multifamily dwelling under the Fair Housing Act?
Covered multifamily dwellings are buildings consisting of four or more dwelling units, if such buildings have one or more elevators; and ground floor dwelling units in other buildings consisting...
-
Side Reach [4.2.6]
High and low reaches are based on a depth of reach no greater than 10 inches measured from the available clear floor space....
-
17 Inch Low Height
The height was measured as the vertical distance from the floor to the lowest point of the seating surface of the mobility device, while the occupant was seated in the device....
-
R304.5.3 Cross Slope
R304.5.3 Cross Slope. The cross slope of curb ramps, blended transitions, and turning spaces shall be 2 percent maximum. At pedestrian street crossings without yield or stop control...
-
Addendum F: Relative Height Differences
Relative heights were calculated for high and low transfers for all three protocols. Refer to Addendum A for the definition of relative height. The following tables F1-F3 represent...
-
1133A.4.1, Item 3
3. The sides of adjacent cabinets and the back wall, which may become exposed to moisture or food handling when a countertop is lowered, shall be constructed of durable, nonabsorbent...
-
1.1.12 Ramp cross slope
1.1.12 Ramp cross slope. Measure for overall cross slope of ramps by establishing elevations at the extreme edges of the ramp at the top and bottom of the ramp and calculate the...
-
1133A.4.1, Item 3
3. The sides of adjacent cabinets and the back wall, which may become exposed to moisture or food handling when a countertop is lowered, shall be constructed of durable, nonabsorbent...
