Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
Search Results "Vertical Platform Lift"
Filters
Commonly Searched Documents
-
703.2.5 Character Height
-
R405.1 General
Clearances are measured in relation to the usable clear space, not necessarily to the vertical support for an element....
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
7.4.5.1 Size
Vertical alignment at the intersection of the trails that form the T-shaped space shall be nominally level....
-
Spout Location [4.15.3]
The trajectory of water flow must be vertically "parallel" or "nearly parallel" to the face of the unit....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
Kompan, Inc. Rock-it GXY934
The generous size of the platform allows up to four kids to play at once, even if they all don’t stay on for long....
-
(3) Adjustability: Transfer Surface Intermediate Heights
For some, independent transfers are only possible when there is minimal or no change in vertical height between the seat of the mobility device and the transfer surface....
-
2.2 Entrances
If there are stairs at entrances, are there also ramps or lifts? Can the accessible entrance be used independently, or is the door heavy or usually locked?...
-
1012.3 Other Vehicles
This section requires parking spaces for vehicles, other than recreational vehicles, to be 16 feet wide minimum to accommodate vans equipped with a lift or ramp....
-
1.3.1 Overview of NPRM
Supine, Prone, or Side-Lying Position (M301) Transfer surface, including height, size, and transfer sides Transfer supports, stirrups, and head and back support Lift...
-
§ 37.42(e)(2)
., where such a clearance would create an insurmountable gap on a mini-high platform or where the physical structure of an existing station does not allow such clearance), barriers must...
-
§ 37.42(e)(2)
., where such a clearance would create an insurmountable gap on a mini-high platform or where the physical structure of an existing station does not allow such clearance), barriers must...
-
§ 36.310(b) Barrier removal
used for transporting individuals (not including barriers that can only be removed through the retrofitting of vehicles or rail passenger cars by the installation of a hydraulic or other lift...
-
Sec.36.310(b) Barrier removal
used for transporting individuals (not including barriers that can only be removed through the retrofitting of vehicles or rail passenger cars by the installation of a hydraulic or other lift...
-
12143(c)(1)(A)(i)
disability who is unable, as a result of a physical or mental impairment (including a vision impairment) and without the assistance of another individual (except an operator of a wheelchair lift...
-
§ 37.123(e)(1)
disability who is unable, as the result of a physical or mental impairment (including a vision impairment), and without the assistance of another individual (except the operator of a wheelchair lift...
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”. ...
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
A7. Curb Ramps
[ADA Stds 4.7.2] Note: 1:12 is one inch of vertical height for each 12 inches in length. Yes _____ No _____...
-
4.5.2 Changes in Level
Changes in level up to 1/4 in (6 mm) may be vertical and without edge treatment (see Fig. 7(c))....
-
4.5.2 CHANGES IN LEVEL
Changes in level up to 1/4 in (6 mm) may be vertical and without edge treatment (see Fig. 7(c))....
-
Handrails [§504.6, §505]
A vertical clearance 9” minimum between upper and lower handrails will help prevent entrapment....
