Aria brackets are available in clear and black anodized aluminum and are secured with color matched set screws....
Search Results "Clear Tread Width"
Filters
Commonly Searched Documents
-
Rakks® Aria Brackets Installation Video
-
EZ-ACCESS Transitions® Angled Entry Plate
Slip-resistant Surface The Transitions Angled Entry Plate features a superior applied tread for high traction....
-
11B-705.1.2.5 Hazardous vehicular areas
Detectable warnings at hazardous vehicular areas shall be 36 inches (914 mm) in width....
-
1133B.5.4.5
SECTION 1133B GENERAL ACCESSIBILITY FOR ENTRANCES, EXITS AND PATHS OF TRAVEL 1133B.5 Ramps. 1133B.5.4.5 Landing width. ...
-
Accessible Route Guidelines
They increase the minimum width for an accessible route from 36 inches to 48 inches....
-
5.7.1 Lift Compatibility Clearance in Base for M301
Where the width of the examination surface is less than 36 inches, the clearance depth shall extend the full width of the equipment....
-
Activar JL Industries Academy Series 1027V10 Aluminum Fire Extinguisher Cabinet
Door and Trim Construction: No. 180 clear anodized aluminum....
-
Are the elements of path of travel and accessible routes substantively the same (such as slope, vertical clearance, width of path of travel, etc.)?
RESPONSE: The terms ACCESSIBLE ROUTE and PATH OF TRAVEL are distinct but related. Accessible route is a fundamental term used to describe, “A continuous unobstructed path connecting...
-
11B-705.1.2.3 Islands or cut-through medians
Detectable warnings at pedestrian islands or cut-through medians shall be 36 inches (914 mm) minimum in depth extending the full width of the pedestrian path or cut-through less 2 inches...
-
11B-406.5.12 Detectable warnings
The detectable warning shall extend the full width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum...
-
§ 38.39(b)
(b) Characters on signs required by paragraph (a) of this section shall have a width-to-height ratio between 3:5 and 1:1 and a stroke width-to-height ratio between 1:5 and 1:10, with a minimum...
-
Emergency Egress
assistance accessible egress routes that coincide with other exit routes to avoid forcing a person using a wheelchair to travel against the general flow increased aisle widths...
-
M301.2.2 Transfer Surface Size
When the transfer surface is located as described above in “A”, the width of the patient scanning/imaging table (side to side) at the designated transfer location should be 28 inches minimum...
-
T402.5 Surfaces
Ramp and bridgeplate surface material shall comply with T302 and extend across the full width and length of the ramp or bridgeplate....
-
11B-705.1.2.5 Blended transitions
Detectable warnings at blended transitions shall be 36 inches (914 mm) in width....
-
3306.2 Walkways
Walkways shall be of sufficient width to accommodate the pedestrian traffic, but in no case shall they be less than 4 feet (1219 mm) in width....
-
3306.2 Walkways
Walkways shall be of sufficient width to accommodate the pedestrian traffic, but in no case shall they be less than 4 feet (1219 mm) in width....
-
LaCantina Contemporary Aluminum Thermally Controlled Door System
0.54 0.52 E180-Air-Clear 0.43 0.43 E240-Air-Clear 0.43...
-
2. Shoulder Breadth
Shoulder Breadth Shoulder breadth tends to be slightly greater than hip or thigh breadth and hence was used as an estimate for the width of an examination table when in a reclined position...
-
Section 35.151(d) Scope of Coverage (Section-by-Section Analysis)
., Advisory 504.4 suggests, but does not require, that covered entities provide visual contrast on stair tread nosing to make them more visible to individuals with low vision). ...
-
Amusement Ride Seats Designed for Transfer: ADA Standard Section 1002.5
The proximity of the clear floor or ground space next to an element and the height of the element one is transferring to are both critical for a safe and independent transfer....
-
11B-1002.5 Amusement ride seats designed for transfer
The proximity of the clear floor or ground space next to an element and the height of the element one is transferring to are both critical for a safe and independent transfer....
-
Technical Requirements
Are the specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.)....
-
Technical Requirements
The specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.). ...
