The clear floor or ground space shall be centered on the kitchen work surface and shall provide knee and toe clearance complying with 306....
Search Results "End Transfer Surface"
-
804.3.1 Clear Floor or Ground Space
-
11B-804.3.1 Clear floor or ground space
The clear floor or ground space shall be centered on the kitchen work surface and shall provide knee and toe clearance complying with Section 11B-306....
-
11B-804.3.1 Clear floor or ground space
The clear floor or ground space shall be centered on the kitchen work surface and shall provide knee and toe clearance complying with Section 11B-306....
-
11B-804.3.1 Clear floor or ground space
The clear floor or ground space shall be centered on the kitchen work surface and shall provide knee and toe clearance complying with Section 11B-306....
-
804.3.1 Clear Floor or Ground Space
The clear floor or ground space shall be centered on the kitchen work surface and shall provide knee and toe clearance complying with 306....
-
804.3.1 Clear Floor or Ground Space
The clear floor or ground space shall be centered on the kitchen work surface and shall provide knee and toe clearance complying with 306....
-
B1. Slope
B1. Is a relatively level (1:50 or 2% maximum slope in all directions) access aisle provided adjacent and parallel to the side of the vehicle pull-up area? [ADA Stds 4.6.6] Yes...
-
1016.7 Slopes
This section contains technical requirements for the maximum running slope and segment length (1016.7.1) and cross slope (1016.7.2) of outdoor recreation access routes.
-
Common Questions (Stairways)
Common Questions
-
Non-Circular Cross Section and Clearance (§505.5, §505.7)
Non-Circular Cross Section and Clearance (§505.5, §505.7)
-
Evaluation of transfers
Based on the guideline criteria in Table 13 pertaining to transfer heights alone (e.g. no gap and no obstacle), 15% of the sample could not transfer to a surface 24” high or higher and 57%...
-
II. Recommendations of Diagnostic Imaging Equipment Manufacturers on Transfer Surface Low Height
transfer surface low height for the following reasons: 1....
-
M305.2.4 Cross Section (Section-by-Section Analysis)
The proposed rule did not provide specific requirements for the cross section of transfer supports....
-
Interior Routes
INTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Carpet pile height 1/2 inch...
-
Interior Routes
INTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Carpet pile height 1/2 inch...
-
Bobrick 18" Straight Grab Bar Peened B-6806.99 x 18
18" (455mm) long, 1-1/2" (38mm) dia. tubing, peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick,...
-
Bobrick 18" Straight Grab Bar B-5806 x 18
18" (455mm) long, 1-1/4" (32mm) dia. tubing. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
-
Bobrick 18" Straight Grab Bar Peened B-5806.99 x 18
18" (455mm) long, 1-1/4" (32mm) dia. tubing , peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm)...
-
Bobrick 18" Straight Grab Bar B-6806 x 18
18" (455mm) long, 1-1/2" (38mm)dia. tubing. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
-
Delta 1-1/2″ x 18″ ADA Grab Bar, Concealed Mounting 40118-PS
Product Features and Benefits 18″ long, 1 1/2″ wide Concealed mounting - mounting hardware included 3″ diameter flanges 1 1/2″ wall clearance Limited Faucet and Finish...
-
11B-203.9 Employee workstations
workstations shall only be required to comply with Sections 11B-207.1 _|Accessible Means of Egress; General|_, 11B-215.3 _|Fire Alarm Systems; Employee Work Areas|_, 11B-302 _|Floor or Ground Surfaces...
-
Bradley Grab Bars 1 1/2" with Concealed Mounting 812
One-piece drawn construction with exposed surfaces in architectural satin finish. Snap over flanges to conceal mounting screws....
