Shoulder alignment generally can be achieved by positioning the back of the bench so it is 8 inches (200 millimeters) closer to the outdoor recreation access route, trail, or beach access...
Search Results "Door Closer"
Filters
Commonly Searched Documents
-
4.4.4 Clear Floor or Ground Space
-
KICK PLATE
An abrasion-resistant plate affixed to the bottom portion of a door to prevent a trap condition and protect its surface. Advisory Definition of KICK PLATE. ...
-
KICK PLATE
An abrasion-resistant plate affixed to the bottom portion of a door to prevent a trap condition and protect its surface. Advisory Definition of KICK PLATE....
-
KICK PLATE
An abrasion-resistant plate affixed to the bottom portion of a door to prevent a trap condition and protect its surface. Advisory Definition of KICK PLATE....
-
11B-705.2 Detectable directional texture
This surface will be placed directly behind the yellow detectable warning texture specified in Section 11B-705.1.2.1, aligning with all doors of the transit vehicles where passengers will...
-
BHMA
ANSI/BHMA A156.10-1999 American National Standard for Power Operated Pedestrian Doors (see 404.3)....
-
EXIT
Exit components include exterior exit doors at the level of exit discharge, interior exit stairways and ramps, exit passageways, exterior exit stairways and ramps and horizontal exits....
-
H1
[ADA Standards § 4.30.6] Yes No If No, install a sign with raised characters and Braille on the wall adjacent to the latch side of the door and centered 60 inches above the...
-
Reach Range
The appliance industry called attention to certain types of doors that, when fully open, cannot easily meet this specification, such as dishwasher doors and doors of ovens and broilers that...
-
11B-410.7 Landing size
ETA Editor's Note There are no requirements for landing size in 2010 ADA Standards, although the door maneuvering clearance requirements at 404.2.4 should be applicable outside the platform...
-
Gates
In the proposed rule, section 404 referenced doors and doorways....
-
F105.2.1 ANSI/BHMA
ANSI/BHMA A156.10-1999 American National Standard for Power Operated Pedestrian Doors (see 404.3)....
-
105.2.1 ANSI/BHMA
ANSI/BHMA A156.10-1999 American National Standard for Power Operated Pedestrian Doors (see 404.3)....
-
105.2.1 ANSI/BHMA
ANSI/BHMA A156.10-1999 American National Standard for Power Operated Pedestrian Doors (see 404.3)....
-
[2010 ADAS] 105.2.1 ANSI/BHMA
ANSI/BHMA A156.10-1999 American National Standard for Power Operated Pedestrian Doors(see 404.3)....
-
1133B.2.3.2
SECTION 1133B GENERAL ACCESSIBILITY FOR ENTRANCES, EXITS AND PATHS OF TRAVEL 1133B.2 Doors. 1133B.2.3.2 Automatic and power-assisted doors. ...
-
[2010 ADAS] 105.2.1 ANSI/BHMA
ANSI/BHMA A156.10-1999 American National Standard for Power Operated Pedestrian Doors (see 404.3)....
-
d. ii.
easy to grasp with one hand and does not require tight grasping and twisting actions of the wrist to operate at the following locations: (1) Main Lobby men's and women's toilet stall doors...
-
4.10.12(4)
Controls shall be located on a front wall if cars have center opening doors, and at the side wall or at the front wall next to the door if cars have side opening doors (see Fig. 23(c) and...
-
4.10.12(4)
Controls shall be located on a front wall if cars have center opening doors, and at the side wall or at the front wall next to the door if cars have side opening doors (see Fig. 23(c) and...
-
Recessed Lavatories
In-swinging doors must clear fixture clearances and door clearances must clear the water closet fixture (verify toilet length)....
-
804.6.2 Operable Parts
Appliance doors and door latching devices shall not be required to comply with 309.4. 2....
-
804.6.2 Operable Parts
Appliance doors and door latching devices shall not be required to comply with 309.4. 2....
-
11B-504.8 Floor identification
required by Chapter 10, Section 1023.9 complying with Sections 11B-703.1, 11B-703.2, 11B-703.3 and 11B-703.5 shall be located at the landing of each floor level, placed adjacent to the door...