These dimensions apply to either forward or side reaches....
Search Results "Side Grab Bar"
Filters
Commonly Searched Documents
-
11B-308.1 General
-
11B-308.1 General
These dimensions apply to either forward or side reaches....
-
1015.3 Height
Exceptions: For occupancies in Group R-3, and within individual dwelling units in occupancies in Group R-2, guards on the open sides of stairs shall have a height not less than 34...
-
11B-604.8.1.1 Size
Wheelchair accessible compartments shall be 60 inches (1524 mm) wide minimum measured perpendicular to the side wall, and 56 inches (1422 mm) deep minimum for wall hung water closets and...
-
SIGNALIZATION OF ROUNDABOUTS
Two of the signals are mounted on posts at the stop bar, and two additional signals are mounted at the upstream side of the crosswalk....
-
Transfer Entry
Transfer Entry There is a large amount of variance in amusement rides and the sides of the ride are often part of the restraint or securement system....
-
K4
, drink, condiment, and tableware dispensers are provided, are dispensers and operating controls mounted no higher than 54 inches above the floor if clear floor space is provided for a side...
-
Jamb Signage
...are all elevator jambs provided with signs placed on both sides designating the floor with 2" minimum height raised letters and Braille characters centered at 60" above the finish floor...
-
I1a
For a side approach (clear floor space at least 30 inches long x 48 inches wide), is the coin slot no higher than 54 inches above the floor?...
-
4.17.4 Toe Clearances
In standard stalls, the front partition and at least one side partition shall provide a toe clearance of at least 9 in (230 mm) above the floor....
-
5e.
Are signs mounted on both sides of the elevator hoistway door opening that designate the floor with 2-inch minimum-height raised letters and Braille characters centered at 60 inches above...
-
Assembly Areas
where they adjoin seating and since accessible routes are required to connect to wheelchair seating locations, compliance with 4.9, including requirements for handrails, is not required at sides...
-
4.17.4 TOE CLEARANCES
In standard stalls, the front partition and at least one side partition shall provide a toe clearance of at least 9 in (230 mm) above the floor....
-
4.34.5.5(4) Controls
In the shower stall in Fig. 35(a), all controls, faucets, and the shower unit shall be mounted on the side wall opposite the seat....
-
Height: ADA Standard Section 704.4.1
accessible telephone because the required 34 inches (865 mm) minimum keypad height can causes the highest operable part of the telephone, usually the coin slot, to exceed the maximum permitted side...
-
FAQ: How do I browse and search content?
Use the search function The search bar is present on each page of Corada. ...
-
4.3.7 Clear Floor Space for Reaching
These dimensions are: (A) occupied width, the horizontal distance between the side-most (lateral-most) points of the wheelchair or occupant on the right and left side; (B) occupied length...
-
Handrails
Handrails are required along both sides of ramps and stairs....
-
Mounting Height and Location
Tactile signs are required to be located alongside the latch side of doors so that clear floor space at least 18 by 18 inches, centered on the tactile characters, is provided outside the...
-
407.4.1 Car Dimensions
Table 407.4.1 Elevator Car Dimensions Minimum Dimensions Door Location Door Clear Width Inside Car, Side...
-
What kinds of treatments constitute maintenance rather than an alteration?
considered maintenance are: painting or striping lanes, crack filling and sealing, surface sealing, chip seals, slurry seals, fog seals, scrub sealing, joint crack seals, joint repairs, dowel bar...
-
B. The Release Includes State and Local Law Claims Which Are Not Addressed By The Agreements
The Release Includes State and Local Law Claims Which Are Not Addressed By The Agreements The Agreements are also overbroad in that they bar class members from bringing claims under state...
-
Aluminum Heavy Duty Wheels n' Heels® InVent Grating
The major difference with the InVent style is that the main support bearing bars are hidden under the top surface bars and run in the direction perpendicular to the top surface bars....
-
Section 35.151(f) Housing at a place of education (Section-by-Section Analysis)
For example, only reinforcements for grab bars need to be provided in residential dwellings, but the actual grab bars must be installed under the transient lodging standards....
