Accessible Parking Spaces for Cars Accessible parking spaces for cars have at least a 60 inch-wide access aisle located adjacent to the designated parking space....
Search Results "Elevator Car Door"
-
A) Accessible Parking
-
Besam SW200i-IG In Ground Swing Door Operator, Center Pivot, Double Door
-
NORTON 5600 Executive Video
Video demonstration of the Norton 5600 Executive Kit.
-
Ezyjamb Installation - The Ezy Jamb system
Ezyjamb - the split type jamb manufactured form cold rolled steel with a patented profile to produce a strong and secure assembly. The unique design of Ezy jamb combines visual...
-
407.4.3 Platform to Hoistway Clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1 1/4 inch (32 mm) maximum....
-
Inclusion Solutions Temporary Lot Paint (Case of 12) Blue
Mark accessible parking spots with this easy to use temporary chalk. Solvent-Based Striping Paint is designed to adhere to a variety of surfaces, especially asphalt and concrete....
-
Inclusion Solutions Paint Marking Stick
Mark your parking lot for accessibility with this easy to use marking stick Easy assembly and operation Uses: Ideal for parking lots, warehouse aisles, school...
-
LaCantina Contemporary Aluminum Thermally Controlled Door System Panel Elevation
Requires the Premium User plan or above. (Login or upgrade your account!) -
1132A.4, Item 3
Secondary exterior doors onto decks, patios, or balcony surfaces constructed of impervious materials (e.g., concrete, brick, flagstone) may have a maximum change in height from the interior...
-
§ 38.113(d)(3) Exception
Where platform set-backs do not allow the horizontal gap or vertical alignment specified in paragraph (d) (1) or (2), platform or portable lifts complying with §38.125(b) of this part, or car...
-
11B-409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (12.7 mm) under rated loading to zero loading conditions....
-
409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (13 mm) under rated loading to zero loading conditions....
-
11B-409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (12.7 mm) under rated loading to zero loading conditions....
-
11B-409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (12.7 mm) under rated loading to zero loading conditions....
-
1009.4.1 Standby power
The elevator shall meet the emergency operation and signaling device requirements of California Code of Regulations, Title 8, Division 1, Chapter 4, Subchapter 6, Elevator Safety Orders....
-
3(1)
(1) On accessible routes in public and common use areas, and for primary entry doors to covered units, doors that comply with ANSI 4.13 would meet this requirement....
-
409.4.4 Leveling
Each car shall automatically stop at a floor landing within a of 1/2 inch (13 mm) under rated loading to zero loading conditions....
-
407.4.3 Platform to Hoistway Clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1¼ inch (32 mm) maximum....
-
Alterations [4.1.6(1)(f) & (k)]
The intended scope of work and technical feasibility are key factors in determining compliance in alterations to existing elevators....
-
11B-407.4.10.2 Surfaces
Support rails shall be smooth and any surface adjacent to them shall be free of sharp or abrasive elements.
-
4.10.10 Floor Surfaces
Floor surfaces shall comply with 4.5.
-
4.1.6(1)(k) EXCEPTION
(k) EXCEPTION:
-
4.10.4(1)
(1) Hall lantern fixtures shall be mounted so that their centerline is at least 72 in (1830 mm) above the lobby floor. (See Fig. 20.)
-
4.10.10 FLOOR SURFACES
Floor surfaces shall comply with 4.5.
