A clear deck space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer wall....
Search Results "Ramp Slope"
Commonly Searched Documents
-
1009.4.1 Clear Deck Space
-
5.8.2.7 Base Support Allowance
An additional sloped region above the base support is permitted at a depth of 25 inches from the front edge of the breast platform at 1½ inches above the floor, and can extend to a height...
-
Exceptions [1014.1, Exceptions 1 and 2]
Many times, the roof of a camp shelter is sloped or does not permit someone to stand fully erect while in the shelter....
-
11B-1009.4.1 Clear deck space
A clear deck space of 60 inches (1524 mm) minimum by 60 inches (1524 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer wall....
-
4.9.4(2)
At the bottom, the handrail shall continue to slope for a distance of the width of one tread from the bottom riser; the remainder of the extension shall be horizontal (see Fig. 19(c) and...
-
Surface and Size [§305.2 and §305.3]
They must be free of level changes and not slope more than 1:48. The minimum size (30” by 48”) applies whether the space is positioned for forward or side approaches....
-
Dispersion: ADA Standard Section 235.2.1
Section 235.2.1 covers scoping requirements in the current ADA Standards for dispersion of boat slips.
-
Platform and Vehicle Floor Coordination: ADA Standard Section 810.5.3
operationally or structurally feasible to meet the horizontal gap or vertical difference requirements of part 1192 or 49 CFR part 38, mini-high platforms, car-borne or platform-mounted lifts, ramps...
-
What is slip resistance?
Materials which might be suitable for level surfaces may be inappropriate for sloping surfaces; materials specified for dry conditions may be unsafe when it rains; a leather shoe may perform...
-
§ 36.304(c)(1)
These measures include, for example, installing an entrance ramp, widening entrances, and providing accessible parking spaces....
-
Sec.36.304(c)(1)
These measures include, for example, installing an entrance ramp, widening entrances, and providing accessible parking spaces....
-
4.1.7(1)(b)
(b) The Advisory Council shall determine, on a case-by-case basis, whether provisions required by part 4 for accessible routes (exterior and interior), ramps, entrances, toilets, parking...
-
§ 38.159(a)(2) Exception
If portable or station-based lifts, ramps or bridge plates meeting the applicable requirements of this section are provided at stations or other stops required to be accessible under regulations...
-
§ 38.171(b)
This provision does not require that inaccessible vehicles be retrofitted with lifts, ramps or other boarding devices....
-
Tent Pads and Tent Platforms
Do not allow the slope of an accessible tent pad or platform to exceed 1:48 (2 percent) in any direction, except when the surface isn't paved or built with boards, the slope may be up to...
-
2. Follow the Accessibility Standards for Play Areas
• The running slope not steeper than 1:16 or 6.25%. • The cross slope shall not be steeper than 1:48 or 2.08%....
- Beneficial Designs The Universal Trail Assessment Process (UTAP)
-
A. Accessible Voting Program
during Early Voting those features of facilities and equipment (including, but not limited to, permanent equipment such as lifts and elevators, and temporary equipment such as portable ramps...
-
11B-705.1.1.4 Resiliency
Exception: Detectable warning surfaces at curb ramps, islands or cut-through medians shall not be required to comply with Section 11B-705.1.1.4....
- Weizel Security 826-S74 SR™ Partition Door
- Corbin Russwin Inc. BLSS Trim Lever Handle & Lockset
- AJW Architectural Products U591 1.6 Gallon Sanitary Napkin Disposal - Surface Mounted
-
Appendix B: Overview of Federal Regulations and Guidance for Detectable Warnings
The ADAAG requires detectable warnings on the full surface of curb ramps. In 1994 the USDOJ, USDOT, and U.S....
-
ASME: ADA Standard Section 105.2.2
Section 105.2.2 of the ADA Standards cover references to the American Society of Mechanical Engineers (ASME) standards.