In no case shall less than 20 percent of the ground floor dwelling units be on an accessible route and comply with the provisions of Division IV. 3....
Search Results "Floor Surface"
Filters
Commonly Searched Documents
-
TEST NO. 2 – SITE ANALYSIS TEST
-
TEST NO. 2 – SITE ANALYSIS TEST
In no case shall less than 20 percent of the ground floor dwelling units be on an accessible route and comply with the provisions of Division IV....
-
Toilet Compartments
The clear floor space required for a baby changing table by TAS 902.2 may overlap the water closet clearance based on TAS 604.3.2 since baby changing tables are considered convenience “fixtures...
-
7(2)(b)(vi)
(vi) Bathtubs and tub/showers located in the bathroom provide a clear access aisle adjacent to the lavatory that is at least 2'6" wide and extends for a length of 4'0" (measured from...
-
McGuire Manufacturing Co., Inc. PW1151AWC: 1 1/2" Offset Sink 151A Stainless Steel Strainer
1 1/2" offset sink assemble with 151A stainless steel basket strainer.
-
McGuire Manufacturing Co., Inc. Heavy Finish Offset Lavatory Strainer
Classic McGuire wheelchair lavatory strainer. Furnished with heavy cast brass grid drain strainer, elbow and 1 1/4" 17GA seamless tubular offset tailpiece. PVD chrome finish. ADA...
-
McGuire Manufacturing Co., Inc. 1151WC: Offset Strainer with 151 Basket Strainer
Offset sink strainer with chrome plated forged brass basket strainer with brass basket. 2 1/8" x 4 1/2" OD.
-
McGuire Manufacturing Co., Inc. PW1149WC: 1 1/2" Offset Sink 149 Flat Strainer
1 1/2" offset sink assemble with 149 brass flat grid strainer.
-
McGuire Manufacturing Co., Inc. 155WC: Offset Lavatory Strainer
Furnished with heavy cast brass grid drain strainer, elbow and 1 1/4" 17GA seamless tubular offset tailpiece. ADA compliant. 8 3/4" x 5 1/8" OD.
-
IPS Corporation Truebro® Lav Shield® Protective Lavatory Enclosure
Lav Shield® provides ADA-compliant undersink protection and meets requirements for wheelchair accessibility. Durable, single-piece construction conceals piping, electronic faucet...
-
McGuire Manufacturing Co., Inc. PW1000WC: 1 1/2" Offset Sink
1 1/2" offset sink assembly prewrapped.
-
McGuire Manufacturing Co., Inc. ProDrainWC: Lavatory Strainer Less Overflow
Offset strainer less overflow. Furnished with heavy brass grid drain strainer, heavy brass elbow and 1 1/4" 17GA seamless tubular brass offset tailpiece.
-
Zurn Industries Rigid Lavatory Enclosure - Vandal Gard
Rigid plastic lavatory enclosure 20" by 18" Conceals all piping, heaters, and other equipment below sink. 3-year warranty
-
McGuire Manufacturing Co., Inc. 1152WC: Offset with 152 Wide Top Strainer
Offset sink strainer with chrome plated wrought brass 4 1/2" wide top sink strainer. 1 3/4" x 4 1/2" OD.
-
McGuire Manufacturing Co., Inc. 1000WC: Offset Strainer - Offset Only
Offset sink strainer wheelchair offset. Allows up to 11" offset for wheelchair access use of most ADA sinks. The offset fits most 1 1/2" direct connect sink strainers including all...
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports....
-
6.1 Q...do the dwelling units on both the first and second stories have to be made accessible?
By defining ground floor to be any floor of a building with an accessible entrance on an accessible route, the Fair Housing Act regulations recognize that certain buildings, based on the...
-
§ 38.125(c)(5) Slope
If the height of the vehicle floor, under 50% passenger load, from which the ramp is deployed is 3 inches or less above the station platform a maximum slope of 1:4 is permitted; if the height...
-
M305.3.1 Horizontal Position
Where the support is horizontal, the top of the gripping surface shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum above the standing surface....
-
M305.3.1.3 Vertical Position
The length of the gripping surface on vertical standing supports shall be 18 inches (455 mm) minimum....
-
4.6.5 PASSENGER LOADING ZONES
Vehicle standing spaces and access aisles shall be level with surface slopes not exceeding 1:50 in all directions....
-
T402.9 Transitions
Vertical surface discontinuities at transitions from boarding and alighting areas to ramps and bridgeplates shall comply with T302.4....
-
4.6.6 Passenger Loading Zones
Vehicle standing spaces and access aisles shall be level with surface slopes not exceeding 1:50 (2%) in all directions....
