The maximum reach depth for this range is 10” measured from the available clear floor space....
Search Results "Sink Depth"
Filters
Commonly Searched Documents
-
Side Reach [§308.3]
-
606.1 General
Lavatories and sinks shall comply with 606. Advisory 606.1 General. If soap and towel dispensers are provided, they must be located within the reach ranges specified in 308....
-
606.1 General
Lavatories and sinks shall comply with 606. Advisory 606.1 General. If soap and towel dispensers are provided, they must be located within the reach ranges specified in 308....
-
606.1 General
Lavatories and sinks shall comply with 606. Advisory 606.1 General. If soap and towel dispensers are provided, they must be located within the reach ranges specified in 308....
-
1133A.7.1 Plumbing protection
Water supply and drain pipes under kitchen sinks shall be insulated or otherwise covered to protect against contact. There shall be no sharp or abrasive surfaces under kitchen sinks....
-
1133A.7.1 Plumbing protection
Water supply and drain pipes under kitchen sinks shall be insulated or otherwise covered to protect against contact. There shall be no sharp or abrasive surfaces under kitchen sinks....
-
11B-606.1 General
Lavatories and sinks shall comply with Section 11B-606. [2010 ADAS] Advisory 606.1 General. ...
-
1133A.7.1 Plumbing protection
Water supply and drain pipes under kitchen sinks shall be insulated or otherwise covered to protect against contact. There shall be no sharp or abrasive surfaces under kitchen sinks....
-
11B-606.1 General
Lavatories and sinks shall comply with Section 11B-606. [2010 ADAS] Advisory 606.1 General....
-
4.24.5 Clear Floor Space
A clear floor space at least 30 in by 48 in (760 mm by 1220 mm) complying with 4.2.4 shall be provided in front of a sink to allow forward approach....
-
4.24.5 CLEAR FLOOR SPACE
A clear floor space at least 30 in by 48 in (760 mm by 1220 mm) complying with 4.2.4 shall be provided in front of a sink to allow forward approach....
-
11B-606.1 General
Lavatories and sinks shall comply with Section 11B-606. Advisory 11B-606.1 General....
-
11B-809.9.4 Work surfaces
maximum above the finish floor with minimum lengths at the following locations as required by this section: Linear length of 30 inches (762 mm) minimum for installation of a sink...
-
Maximum side reach ranges. (Section-by-Section Analysis)
Reach ranges apply to a variety of building elements, including light switches, key pads, electrical outlets, fire alarm pulls, card readers, thermostats, elevator controls, pay...
-
G. Compartment Size
G. If the accessible toilet is in a stall, does the stall measure at least 60" wide and 56" deep if it is wall mounted or 59" deep if it is floor mounted to allow persons who use...
-
Side Approach and Reach
[See subsections ...]
-
Obstructed High Reach
The maximum high reach is reduced to 46” when the reach over an obstruction is deeper than 10” (to a maximum of 24”). Obstructions at side reaches are limited to a height of...
-
Moen M–Dura Chrome Two-Handle Utility Faucet 8277
Moen Commercial's line of M–DURA™ heavy–duty products are built to last with vandal–resistant features to help reduce your facility's maintenance costs. Ideal for high–traffic...
-
Moen M-DURA Chrome Two-Handle Utility Faucet 8126
Moen Commercial's line of M–DURA™ heavy–duty products are built to last with vandal–resistant features to help reduce your facility's maintenance costs. Ideal for high–traffic...
-
Moen M–Dura Chrome Two-Handle Utility Faucet 8121
M–DURA faucets feature solid cast brass construction heavy–duty quarter turn ceramic disc cartridge with a durable brass shell; internal stops prevent misalignment,...
-
Moen M–Dura Chrome Two-Handle Utility Faucet 8119
M–DURA faucets feature solid cast brass construction heavy–duty quarter turn ceramic disc cartridge with a durable brass shell; internal stops prevent misalignment,...
-
Knee and Toe Clearance
Accessible lavatories and sinks must provide knee and toe clearance for a forward approach (606.2)....
-
1133A.4.1, Item 1
Sinks and work surfaces required by Section 1133A.4 shall be designed to enable repositioning to a minimum height of 28 inches (711 mm)....
-
1133A.4.1, Item 1
Sinks and work surfaces required by Section 1133A.4 shall be designed to enable repositioning to a minimum height of 28 inches (711 mm)....
