Projection Recess: 4" (102mm) 4" (102mm). Gals.: 12 (46 L)...
Search Results "Recessed Door"
Filters
Commonly Searched Documents
-
American Specialties Semi-Recessed Waste Receptacle 0458
-
11B-604.8.2.2 Doors
11B-604.8.2.2 Doors....
-
11B-407.3 Elevator door requirements
Hoistway and car doors shall comply with Section 11B-407.3....
-
11B-407.3 Elevator door requirements
Hoistway and car doors shall comply with Section 11B-407.3....
-
11B-407.3 Elevator door requirements
Hoistway and car doors shall comply with Section 11B-407.3....
-
AJW Architectural Products U2314 Unidoor C-fold/Multifold Towel Dispenser - Recessed
Uni-Door: Fabricated of #18 ga stainless steel with a #4 satin finish with 1/2" returns to wall surface....
-
AJW Architectural Products U2304 Unidoor C-fold/Multifold Towel Dispenser - Recessed
Uni-Door: Fabricated of #18 ga stainless steel with a #4 satin finish & 1/2" returns to wall surface....
-
AJW Architectural Products U2324 Unidoor C-fold/Multifold Towel Dispenser - Recessed
Uni-Door: Fabricated of #18 ga stainless steel with a #4 satin finish with 1/2" returns to wall for rigidity....
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
Revolving Doors or Turnstiles
A commenter advised that no revolving doors or turnstiles should be permitted on an accessible route. Response....
-
4.13.9* DOOR HARDWARE
When sliding doors are fully open, operating hardware shall be exposed and usable from both sides....
-
Door and Gate Hardware
Section 404.2.7 also covers the operating characteristics and height of door and gate hardware....
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
11B-604.8.1.2 Doors
11B-604.8.1.2 Doors....
-
11B-604.8.1.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404 except that if the approach is from the push side of the compartment door, clearance between the door...
-
11B-604.8.1.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404 except that if the approach is from the push side of the compartment door, clearance between the door...
-
American Specialties Recessed Waste Receptacle 04733
Recessed Waste Receptacle shall hold 3.1gal. (11.6 liters) of dry/solids waste and shall be fabricated of 22 gauge, type 304, 18-8 alloy stainless steel with No 4 finish protected by a polyvinyl...
-
11B-404.2.8.1 Door closers and gate closers
Door closers and gate closers shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum...
-
11B-404.2.8.1 Door closers and gate closers
Door closers and gate closers shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum...
-
11B-411.3.5 Width
The width of elevator doors shall comply with Table 11B-407.4.1....
-
Doors in a Series
A few commenters expressed concern that the Guidelines did not provide design for an entrance that consists of a series of more than one door....
-
11B-404.2.8.1 Door closers and gate closers
Door closers and gate closers shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum...
-
Is compliance on both sides of a door or gate required when it is usable only from one side?
No, compliance is not required on both sides of those doors or gates that can be used in one direction only. Compliance is required only on the usable side....
-
11B-409.3 Elevator doors
Hoistway doors, car doors, and car gates shall comply with Sections 11B-409.3 and 11B-404....
