specify the following dimensions for grab bars to enable individuals with disabilities to firmly grasp the grab bars and support themselves during transfers: • Grab bars with circular cross...
Search Results "Dune Crossing"
Filters
Commonly Searched Documents
-
Cross Section of Gripping Surfaces
-
1.1.2 Walks
Measure walks and other non - ramp pedestrian surfaces for overall running slope and cross slope as well as local running slope and cross slope variations (flatness) in accordance with 1.1.3...
-
11B-406.5.1 Location
Curb ramps at marked crossings shall be wholly contained within the markings, excluding any flared sides. Exception: Diagonal curb ramps shall comply with Section 11B-406.5.9....
-
M305.2.4.1 Circular Cross Section
Transfer supports with circular cross sections shall have an outside diameter of 1 ¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
Trail Slopes
Cross slopes that are too steep can be difficult to traverse, but trails with too little cross slope tend to become streams. Water running down or ponding on trails destroys them....
-
1017.7 Slopes
This section contains technical requirements for the maximum running slope and segment length (1017.7.1) and cross slope (1017.7.2) of trails....
-
403.3 Slope
The cross slope of walking surfaces shall not be steeper than 1:48....
-
403.3 Slope
The cross slope of walking surfaces shall not be steeper than 1:48....
-
403.3 Slope
The cross slope of walking surfaces shall not be steeper than 1:48....
-
M305.2.4.2 Non-Circular Cross Section
Transfer supports with non-circular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (100 mm) minimum and 4.8 inches...
-
Step 3: Apply the Accessibility Provisions
This step involves looking at FSTAG, sections 7.4.1 through 7.4.8, which contain the technical requirements for trail grade, cross slope, resting interval, surface, clear tread width, passing...
-
1. & 2. Sidewalk Slope
1. ...do the sidewalks have cross slopes (i.e.: slopes tilting side to side) less than 1:50 (critical dimension of ´" or less) [sic] so persons who use wheelchairs can conveniently negotiate...
-
4.7.10 Diagonal Curb Ramps
If diagonal curb ramps are provided at marked crossings, the 48 in (1220 mm) clear space shall be within the markings (see Fig. 15(c) and (d))....
-
1.1.5
1.1.5 A maximum design cross slope for accessible exterior pedestrian paving and ramps of 1.5% (1:67 or about 3/16 in. per ft. [15 mm per m]) is recommended....
-
4.7.10 DIAGONAL CURB RAMPS
If diagonal curb ramps are provided at marked crossings, the 48 in (1220 mm) clear space shall be within the markings (see Fig. 15(c) and (d))....
-
4.3.7 Slope
Nowhere shall the cross slope of an accessible route exceed 1:50....
-
4.3.7 SLOPE
Nowhere shall the cross slope of an accessible route exceed 1:50....
-
R404.2 Surfaces
Surfaces of clear spaces shall comply with R302.7 and shall have a running slope consistent with the grade of the adjacent pedestrian access route and cross slope of 2 percent maximum....
-
Resting Intervals on Trails
Design Tip The cross slope requirement depends on what material is used....
-
11B-406.5.9 Clear space at diagonal curb ramps
Diagonal curb ramps provided at marked crossings shall provide the 48 inches (1219 mm) minimum clear space within the markings....
-
11B-406.5.9 Clear space at diagonal curb ramps
Diagonal curb ramps provided at marked crossings shall provide the 48 inches (1219 mm) minimum clear space within the markings....
-
11B-406.5.9 Clear space at diagonal curb ramps
Diagonal curb ramps provided at marked crossings shall provide the 48 inches (1219 mm) minimum clear space within the markings....
-
Diagonal Curb Ramps: ADA Standard Section 406.6
Section 406.6 covers the current ADA Standards for diagonal curb ramps.
-
Accessible Sidewalks 3: Pedestrians with Low Vision
Requires the Registered User plan or above. Login!