Curbs or barriers shall extend 2 inches (51 mm) minimum above the surface of the fishing pier or platform....
Search Results "Stable Surface"
Filters
Commonly Searched Documents
-
11B-1005.3.1 Curb or barrier
-
11B-609.4 Position of grab bars
Grab bars shall be installed in a horizontal position, 33 inches (838 mm) minimum and 36 inches (914 mm) maximum above the finish floor measured to the top of the gripping surface, except...
-
Attachment I
All spaces and access aisles for persons with disabilities shall be flat and level, with slopes and cross-slopes not exceeding 1:50 in all directions, and their surfaces shall be firm, stable...
-
11B-809.8 Doors
The floor or landing at primary entry doors, required exit doors, and secondary exit doors where a change in elevation occurs between the interior and the exterior surface of the floor or...
-
11B-502.3.3 Marking
The area within the blue borderlines shall be marked with hatched lines a maximum of 36 inches (914 mm) on center in a color contrasting with that of the aisle surface, preferably blue or...
-
BOAT LAUNCH RAMP
[DSA-AC] A sloped surface designed for launching and retrieving trailered boats and other water craft to and from a body of water....
-
HEWI Hinged Support Rail Duo WARM TOUCH
plate made of metal with cap made of environmentally friendly, chrome-look coated polyamide - wall mounting plate 181 mm high and 130 mm wide - top rail ø 33 mm, bottom rail ø 25 mm - stable...
-
11B-1009.2.7 Operation
The lift shall be stable and not permit unintended movement when a person is getting into or out of the seat. [2010 ADAS] 1009.2.7 Operation. ...
-
11B-1009.2.7 Operation
The lift shall be stable and not permit unintended movement when a person is getting into or out of the seat. [2010 ADAS] 1009.2.7 Operation....
-
11B-502.6.4 Marking
Each accessible car and van space shall have surface identification complying with either Section 11B-502.6.4.1 or 11B-502.6.4.2....
-
RAMP
A walking surface that has a running slope steeper than one unit vertical in 20 units horizontal (5-percent slope)....
-
Back Support: ADA Standard Section 903.4
Back support shall be 42 inches (1065 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (455 mm) minimum above the seat...
-
11B-705.1.1.3 Color and contrast
Detectable warning surfaces shall comply with Section 11B-705.1.1.3.1. The material used to comply with this section shall be an integral part of the detectable warning surface....
-
11B-1007.2 Accessible routes
Accessible routes located on playing surfaces of miniature golf holes shall be permitted to use the exceptions in Section 11B-1007.2....
-
Size: ADA Standard Section 1008.3.1.1
Transfer platforms shall have level surfaces 14 inches (355 mm) deep minimum and 24 inches (610 mm) wide minimum....
-
Size: ADA Standard Section 1008.3.2.1
Transfer steps shall have level surfaces 14 inches (355 mm) deep minimum and 24 inches (610 mm) wide minimum....
-
11B-1008.3.2.1 Size
Transfer steps shall have level surfaces 14 inches (356 mm) deep minimum and 24 inches (610 mm) wide minimum....
-
11B-1008.3.1.1 Size
Transfer platforms shall have level surfaces 14 inches (356 mm) deep minimum and 24 inches (610 mm) wide minimum....
-
Mirrors: ADA Standard Section 603.3
Section 603.3 covers the current ADA Standards for mirrors in toilet and bathing rooms.
-
11B-705.1.1.1 Dome size
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (22.9 mm) minimum and 0.92 inch (23.4 mm) maximum, a top diameter of 0.45 inch (11.4 mm) minimum and...
-
11B-603.3 Mirrors
Mirrors located above lavatories or countertops shall be installed with the bottom edge of the reflecting surface 40 inches (1016 mm) maximum above the finish floor or ground....
-
BraunAbility Millenium 2 Wheelchair Lift for School Buses, Cutaway Buses, and Paratransit Vans
Those who appreciate a strong, stable lifting platform can choose this wheel chair lift series with confidence....
-
Height: ADA Standard Section 903.5
The top of the bench seat surface shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the finish floor or ground....
