Top loading machines shall have the door to the laundry compartment located 36 inches (915 mm) maximum above the finish floor. Front loading machines shall have the bottom of the...
Search Results "Seat Height"
-
611.4 Height
-
407.3.3.1 Height
The device shall be activated by sensing an obstruction passing through the opening at 5 inches (125 mm) nominal and 29 inches (735 mm) nominal above the finish floor.
-
309.3 Height
Operable parts shall be placed within one or more of the reach ranges specified in 308.
-
811.3 Height
Storage elements shall comply with at least one of the reach ranges specified in 308.
-
407.4.6.4.1 Height
Emergency control buttons shall have their centerlines 35 inches (890 mm) minimum above the finish floor.
-
407.2.1.1 Height
Call buttons and keypads shall be located within one of the reach ranges specified in 308, measured to the centerline of the highest operable part. EXCEPTION: Existing call...
-
4. Seating Plans for Designed Theaters and Future Construction Theaters
Seating Plans for Designed Theaters and Future Construction Theaters The United States has reviewed and specifically approves the auditoria seating plans for the Designed Theaters set...
-
Dispersion of Wheelchair Seating Areas (Section-By-Section Analysis and Response to Comments)
- Dispersal of wheelchair seating areas in theaters will be required only where there are more than 300 seats, rather than in all cases....
-
Does a wheelchair user have to use the seat belt and shoulder harness?
Transit operators may establish a policy that requires the seat belt and shoulder harness to be used by all riders, including those who use wheelchairs as well as those who use vehicle seats...
-
§ 35.138(h) Prevention of fraud in purchase of tickets for accessible seating
(h) Prevention of fraud in purchase of tickets for accessible seating....
-
Does a wheelchair user have to use the seat belt and shoulder harness?
Transit operators may establish a policy that requires the seat belt and shoulder harness to be used by all riders, including those who use wheelchairs as well as those who use vehicle seats...
-
General: ADA Standard Section 803.1
Section 903.5 requires dressing room bench seats to be installed so that they are at the same height as a typical wheelchair seat, 17 inches (430 mm) to 19 inches (485 mm)....
-
Wheelchair seating locations must be provided in all areas
• Wheelchair seating locations must be provided in all areas including sky boxes and specialty areas....
-
California Department of Managed Health Care - Physical Access to Health Care Fact Sheet
If You Use a Wheelchair or Have a Hard Time Walking
-
Requirement 6 -- Reinforced Walls for Grab Bars
[See subsections ...]
-
Grainger Tough Guy Stainless Steel Sanitary Napkin Receptacle, 11" Height
Stainless Steel Sanitary Napkin Receptacle, 11" Height, 1 EA Item# 1ECK9 Mfr....
-
§ 35.138(h) Prevention of fraudulent purchase of accessible seating
(h) Prevention of fraudulent purchase of accessible seating. A public entity may not require proof of disability before selling a wheelchair space....
-
Two Step Transfers Attainable Heights
Maximum attainable height difference in two step transfer percentiles (in inches) Percentiles Protocol 5th...
-
11B-803.1 General
Section 11B-903.5 requires dressing room bench seats to be installed so that they are at the same height as a typical wheelchair seat, 17 inches (430 mm) to 19 inches (485 mm)....
-
11B-803.1 General
Section 11B-903.5 requires dressing room bench seats to be installed so that they are at the same height as a typical wheelchair seat, 17 inches (430 mm) to 19 inches (485 mm)....
-
Hotel Bed Height
Thanks, Kaylan. This is very helpful. I did not know you responded to my question until today. I wish Corada would send an email to alert you that someone responded to your...
-
1011.5.2 Riser height and tread depth
... Exceptions: 4. ... [DSA-AC] For applications listed in Section 1.9.1 regulated by the Division of the State Architect-Access Compliance, see Chapter 11B, Section...
-
1011.5.2 Riser height and tread depth
... Exceptions: 4. ... [DSA-AC] For applications listed in Section 1.9.1 regulated by the Division of the State Architect-Access Compliance, see Chapter 11B, Section...
-
T402.8.1 Deployment to Roadways or to Curb Height Boarding and Alighting Areas
The running slope of ramps and bridgeplates used for deployment to the roadway or to curb-height boarding and alighting areas shall be 1:6 maximum, as measured to ground level with the non-rail...
