Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
Search Results "Extended Floor Surface"
-
505.7.1 Circular Cross Section
-
11B-505.7.1 Circular cross section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
11B-505.7.1 Circular cross section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
11B-505.7.1 Circular cross section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
Smith System Flex Single-Student Desk 01368 & 01371
Patented backpack peg keeps students items organized and off the floor. Backpack peg can be positioned inside or outside of either leg. ...
-
Smith Carrel Hi-Lo Study Carrel - "The Original"
The front edge of the work surface has soft rounded 3mm edge banding for arm comfort....
-
Fixtures
Fixtures TAS 604.3.2 also allows the clear floor space and clearances required at other “fixtures” to overlap the water closet clearance....
-
Station platforms
Station platforms must be coordinated with the vehicle floor height. (DOT ADA Standard 810.5.3.)...
-
1008.2.6.2 Use Zones
Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition) (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1 1/4 inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1 1/4 inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
D. Chapter 3: Building Blocks
Chapter 3 in the 2016 Non-Rail Vehicle Guidelines contains the technical requirements related to three areas—walking surfaces (T302), handrails, stanchions, and handholds (T303), and operable...
-
§ 38.107(a)(1)
(1) The minimum clear floor area shall be 35 inches by 60 inches....
-
5.2 Transfer Surface Size Recommendations
5.2 Transfer Surface Size Recommendations...
-
F231.3 Holding Cells
Where provided, central holding cells and court-floor holding cells shall comply with F231.3....
-
231.3 Holding Cells
Where provided, central holding cells and court-floor holding cells shall comply with 231.3....
-
5.3.2.1 Size
The clear floor or ground space shall be 60 inches (1525 mm) wide minimum measured parallel with the back of the pit toilet, and 56 inches (1420 mm) deep minimum measured parallel to the...
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
M301.2.1 Adjustability (Section-by-Section Analysis)
The MDE NPRM proposed a transfer surface height range for diagnostic equipment used by patients in the supine, prone, or side-lying position of 17 inches minimum and 19 inches maximum....
-
Location: ADA Standard Section 703.4.2
Signs containing tactile characters shall be located so that a clear floor space of 18 inches (455 mm) minimum by 18 inches (455 mm) minimum, centered on the tactile characters, is provided...
-
Seating [4.32.2] and Knee Clearance [4.32.3]
The over-the-surface reach is limited to 25 inches if at least this much space is available below for knees and toes; (the forward seated reach may not extend beyond the toes)....
-
11B-231.3 Holding cells
Where provided, central holding cells and court-floor holding cells shall comply with Section 11B-231.3. ...
-
11B-231.3 Holding cells
Where provided, central holding cells and court-floor holding cells shall comply with Section 11B-231.3....
