A door can be recessed due to wall thickness or because of the placement of casework and other fixed elements adjacent to the doorway....
Search Results "Plumbing Element"
-
404.2.4.3 Recessed Doors and Gates
-
707.1 General
Place accessible gates and fare vending machines in close proximity to other accessible elements when feasible so the facility is easier to use....
-
Gripping Surface Cross Section and Clearances M301, M302, and M305.2
Gripping Surface Cross Section and Clearances M301, M302, and M305.2 Gripping surface for transfer supports shall be free of sharp or abrasive elements and shall have rounded edges per...
-
707.1 General
Place accessible gates and fare vending machines in close proximity to other accessible elements when feasible so the facility is easier to use....
-
106.5.68 Technically Infeasible
removing or altering a load-bearing member that is an essential part of the structural frame; or because other existing physical or site constraints prohibit modification or addition of elements...
-
Alteration
Alterations include, but are not limited to, remodeling, renovation, rehabilitation, reconstruction, historic restoration, changes or rearrangement of the structural parts or elements, and...
-
Audible Alarms [4.28.2]
Recommendation: Alarms with a periodic element to the signal, such as single stroke bells, hi-low, and fast whoop, are considered more effective than those with continuous or reverberating...
-
Width [4.3.3.] and Passing Space [4.3.4]
However, the minimum width of hallways and corridors is often further determined by ADAAG requirements for clear floor space at elements such as drinking fountains, door maneuvering clearances...
-
Alteration of a recreation site, building, or facility
remodeling, renovation, rehabilitation, reconstruction, historic restoration, change in surface of circulation paths or vehicular ways, changes or rearrangement of the structural parts or elements...
-
TEMPORARY
Temporary as applied to elements means installed for less than 6 months and not required for safety reasons....
-
1.1.9 Horizontal gaps and vertical alignment
Measure for local horizontal discontinuities and variations in vertical alignment such as at concrete joints, gaps, grade breaks, and at the interface of concrete with other materials or elements...
-
4 - Best practices for construction observation
4 - Best practices for construction observation Construction observation is the final step in building an accessible element to meet design and regulatory requirements....
-
Surface and Size [§305.2 and §305.3]
Additional space is required when the space is confined on three sides and is obstructed for more than half the depth, such as when elements are recessed in alcoves....
-
Alterations and Additions
Users of this guide must familiarize themselves with the specific scoping requirements that apply to each element, building, facility, or site that is subject to the Standards adopted to...
-
ACCESSIBLE ROUTE
[DSA-AC & HCD 1-AC] A continuous unobstructed path connecting accessible elements and spaces of an accessible site, building or facility that can be negotiated by a person with a disability...
-
11B-403.5.2 Clear width at turn
Where the accessible route makes a 180 degree turn around an element which is less than 48 inches (1219 mm) wide, clear width shall be 42 inches (1067 mm) minimum approaching the turn, 48...
-
1.1.7.3.1 Detached one- and two-family dwellings
egress, and their accessory structures, may be designed and constructed in accordance with this code or the California Residential Code, but not both, unless the proposed structure(s) or element...
-
11B-403.5.2 Clear width at turn
Where the accessible route makes a 180 degree turn around an element which is less than 48 inches (1219 mm) wide, clear width shall be 42 inches (1067 mm) minimum approaching the turn, 48...
-
ACCESSIBLE ROUTE
[DSA-AC & HCD 1-AC] A continuous unobstructed path connecting accessible elements and spaces of an accessible site, building or facility that can be negotiated by a person with a disability...
-
212 Sinks, Kitchens, and Kitchenettes
Comments, including those representing the hotel and motel industry, considered this reference to be unnecessary since such elements are adequately covered through references to kitchenettes...
-
103 Equivalent Facilitation
Departure from the explicit technical and scoping requirements of this code for any element voids any otherwise applicable presumption of rebuttable evidence that the element has been constructed...
-
205 and 309 Operable Parts
205 and 309 Operable Parts Section 4.1.3, and more specifically sections 4.1.3(13), 4.27.3, and 4.27.4 of the 1991 Standards, require operable parts on accessible elements, along accessible...
-
3. MINIMUMS, MAXIMUMS AND SPECIFYING AT THE LIMIT
MINIMUMS, MAXIMUMS AND SPECIFYING AT THE LIMIT: Where an element is to be installed at the minimum or maximum permitted dimension, such as "48 inches maximum", it is not good practice to...
-
Alternative Golf Car Passage
A golf car passage can be substituted for all or part of the accessible route connecting elements within the boundary of the course and must be a minimum of 48 inches in width....