5.9.2 Standing Supports on Ramped Entry Raised Platforms with Wheelchair Spaces Recommendations...
Search Results "Ramp Surface"
-
5.9.2 Standing Supports on Ramped Entry Raised Platforms with Wheelchair Spaces Recommendations
-
11B-813.2.1.2 Clearance
Floor or ground surfaces of clearances shall comply with Section 11B-302. Changes in level are not permitted....
-
11B-813.2.1.2 Clearance
Floor or ground surfaces of clearances shall comply with Section 11B-302. Changes in level are not permitted....
-
R304.5.1.2 Shared Use Paths
In shared use paths, the width of curb ramps runs and blended transitions shall be equal to the width of the shared use path....
-
Built-in Elements
BUILT-IN ELEMENTS Dining/work surfaces 11B-226, 11B-902.2 Benches 11B-903.2...
-
Built-in Elements
BUILT-IN ELEMENTS Dining/work surfaces 11B-226, 11B-902.2 Benches 11B-903.2...
-
R302.6 Cross Slope
Cross slope requirements are contained in R304.5.3 for curb ramps and blended transitions, and in R407.3 for ramps....
-
11B-804.3 Kitchen work surface
In residential dwelling units required to comply with Section 11B-809, at least one 30 inches (762 mm) wide minimum section of counter shall provide a kitchen work surface that complies...
-
11B-1003.3.2 Boarding pier clearances
The following example applies to a boat launch ramp boarding pier: A chain of floats is provided on a launch ramp to be used as a boarding pier which is required to be accessible by Section...
-
Detecto 6550 Portable Wheelchair Scale
It can be used with wheelchairs, straight-legged chairs or as a stand-on scale, and its sloped ramps offer versatility by allowing entry from either side....
-
810.5.1 Slope
Rail platforms shall not exceed a slope of 1:48 in all directions. EXCEPTION: Where platforms serve vehicles operating on existing track or track laid in existing roadway, the...
-
11B-810.5.1 Slope
Rail platforms shall not exceed a slope of 1:48 in all directions. Exception: Where platforms serve vehicles operating on existing track or track laid in existing roadway, the...
-
Wayfinding is more than just graphics (slides 2 – 4)
Cognitive process (slides 2 - 4). [Wayfinding is] really more of a cognitive process. You gather information at the beginning. You cite and execute a path to take. And then you...
-
A. Slope at Door
A. If a fully automatic door is not provided, is the walkway in front of the lobby door level, without any portion steeper than 1:50 (critical dimension of ´" or less), so persons...
-
A4.13.9 Door Hardware
Some disabled persons must push against a door with their chair or walker to open it. Applied kickplates on doors with closers can reduce required maintenance by withstanding abuse...
-
A4.13.9 DOOR HARDWARE
Some disabled persons must push against a door with their chair or walker to open it. Applied kickplates on doors with closers can reduce required maintenance by withstanding abuse...
-
APPENDIX C
APPENDIX C On‐Site Inspection Form ETA Editor's Note Click here to download the pdf version of the document with the ON-SITE INSPECTION FORM in APPENDIX C, pdf page 41.
-
11B-810.5.1 Slope
Rail platforms shall not exceed a slope of 1:48 in all directions. Exception: Where platforms serve vehicles operating on existing track or track laid in existing roadway, the...
-
11B-810.5.1 Slope
Rail platforms shall not exceed a slope of 1:48 in all directions. Exception: Where platforms serve vehicles operating on existing track or track laid in existing roadway, the...
-
810.5.1 Slope
Rail platforms shall not exceed a slope of 1:48 in all directions. EXCEPTION: Where platforms serve vehicles operating on existing track or track laid in existing roadway, the...
-
810.5.1 Slope
810.5.1 Slope. Rail platforms shall not exceed a slope of 1:48 in all directions. EXCEPTION: Where platforms serve vehicles operating on existing track or track laid in existing...
-
5.1 Transfer Surface Height
5.1 Transfer Surface Height...
-
226.1 General
Where dining surfaces are provided for the consumption of food or drink, at least 5 percent of the seating spaces and standing spaces at the dining surfaces shall comply with 902....
