The latter includes studies to determine optimum design specifications, such as: toilet height and location, grab bar height, positioning, and location; clear floor space; and size of fixtures...
Search Results "Counter Height"
Filters
Commonly Searched Documents
-
RECOMMENDATIONS
-
1.1.17 Stairs
Measure cast - in - place stairs for both riser height and tread depth of each riser and tread....
-
11B-809.10.7.3 Reinforcement for grab bars
The grab bar reinforcement shall be 8 inches (203 mm) minimum in height. The backing shall 40 (sic) inches (1016 mm) minimum in length....
-
Lowered section for bar
Can anyone show me where a folding lower section of the bar counter can't be used as long as it meets the other requirements? This is not for designing a new bar....
-
Rakks® Brackets Installation Video
Depending on length and load capacities, brackets are manufactured in 1-1/4” and 2” heights. Rakks Style brackets have excellent lateral support and work well as bookends....
-
11B-703.6.1 Pictogram field
Pictograms shall have a field height of 6 inches (152 mm) minimum. Characters and Braille shall not be located in the pictogram field. Advisory 11B-703.6.1 Pictogram field. ...
-
1. Measuring Tape
A metal measuring tape is an essential tool for a successful survey because many of the accessibility requirements concern the width, height, or depth of various features....
-
Signs
Signs that provide direction to, or information, about functional spaces must only comply with requirements for character proportion, character height, and finish and contrast between the...
-
Alteration
rehabilitation, reconstruction, historic restoration, changes or rearrangement of the structural parts or elements, and changes or rearrangement in the plan configuration of walls and full-height...
-
Verify Rough Plumbing
Location of lavatory traps from side walls. 11B-606.6 Location of bathtub controls and drain. 11B-607.5 Installation height...
-
4.29.2* Detectable Warnings on Walking Surfaces
Detectable warnings shall consist of raised truncated domes with a diameter of nominal 0.9 in (23 mm), a height of nominal 0.2 in (5 mm) and a center-to-center spacing of nominal 2.35 in...
-
Verify Rough Plumbing
Location of lavatory traps from side walls. 11B-606.6 Location of bathtub controls and drain. 11B-607.5 Installation height...
-
4.1.3 Wheelchair Seating Space
Toe clearance of at least 9 inches (230 mm) in height shall extend at least an additional 5 inches (125 mm) from the knee clearance....
-
Knee Clearance: Clearance as Measured from Anterior-Most Point - Manual Wheelchair
It references dimensions of clearance height and depth to the forward-most point on the person or mobility device (e.g., toe, footrest)....
-
Knee Clearance: Clearance as Measured from Dorsal Foot Point - Manual Wheelchair
It references dimensions of clearance height and depth to the dorsal foot point on a person (e.g., top of ankle)....
-
M303.2.4.2 Knee Clearance
Between 9 inches (230 mm) and 27 inches (685 mm) above the floor, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for every 6 inches (150 mm) in height...
-
11B-707.9.1.1 Tactilely discernible numerical keypad
A tactilely discernible numerical keypad similar to a telephone keypad containing a raised dot with a dot base diameter between 1.5 mm and 1.6 mm and a height between 0.6 mm and 0.9 mm on...
-
MAKING THE BUILT ENVIRONMENT ACCESSIBLE
no access aisle to allow deployment of a van’s wheelchair lift, steps at a facility’s entrance or within its serving or selling space, aisles too narrow to accommodate mobility devices, counters...
-
205.1 General
Where two or more outlets are provided in a kitchen above a length of counter top that is uninterrupted by a sink or appliance, one outlet shall not be required to comply with 309. 4....
-
Common Requirements (R304.5) (Section-by-Section Analysis)
A maximum counter slope of 5 percent is specified for the gutter or street at the foot of curb ramp runs, blended transitions, and turning spaces....
-
20. DESIGN AND CONSTRUCTION STANDARDS
., signage, front desk counter) for any Brand, it shall ensure that such designs comply with the ADA Standards....
-
1. General Exception
Some specific examples include: Dual Energy X-Ray Absorptiometry (DXA) machines, with a mechanism that moves imaging components along a track beneath the patient surface precluding height...
-
803.1 General
Section 903.5 requires dressing room bench seats to be installed so that they are at the same height as a typical wheelchair seat, 17 inches (430 mm) to 19 inches (485 mm)....
