[2010 ADA Standards] EXCEPTION: Alterations to cells shall not be required to comply except to the extent determined by the Attorney General....
Search Results "Altered Elevator"
-
11B-232.3 Special holding cells and special housing cells
-
232.3 Special Holding Cells and Special Housing Cells
EXCEPTION: Alterations to cells shall not be required to comply except to the extent determined by the Attorney General....
-
11B-408.2.3 Hoistway signs
Signs at elevator hoistways shall comply with Section 11B-407.2.3.1....
-
11B-408.2.3 Hoistway signs
Signs at elevator hoistways shall comply with Section 11B-407.2.3.1....
-
11B-408.2.3 Hoistway signs
Signs at elevator hoistways shall comply with Section 11B-407.2.3.1....
-
§8.32(a)
(a) Effective as of July 11, 1988, design, construction, or alteration of buildings in conformance with sections 3-8 of the Uniform Federal Accessibility Standards (UFAS) shall be deemed...
-
408.2.3 Hoistway Signs
Signs at elevator hoistways shall comply with 407.2.3.1....
-
Q2: Milling a Road Surface
Q2: The Joint Technical Assistance states that “[r]esurfacing is an alteration that triggers the requirement to add curb ramps if it involves work on a street or roadway spanning from one...
-
Inaccessible Town Program
This temporary solution assures that the service, program, or activity is accessible during the time the alterations are planned and being implemented....
-
VALUATION THRESHOLD
. ◼ 2016 Valuation Threshold for Alterations, Structural Repairs or Additions to Existing Buildings In accordance with the 2013 California Building Code Chapter 2 definition...
-
VALUATION THRESHOLD
dating back to 2000 are available on the Division of the State Architect web site at: http://www.dgs.ca.gov/dsa/Programs/progAccess/threshold.aspx◼ 2016 Valuation Threshold for Alterations...
-
1. Under Title II, what must public school districts do to provide effective communication to students with hearing, vision, or speech disabilities?
student.21 If, after complying with the process described in Q&A 6, a public school district can prove that providing a particular auxiliary aid or service would be a fundamental alteration...
-
Section 36.302 Modifications in Policies, Practices, or Procedures (Preamble, Section-by-Section Analysis)
The rule enunciated in § 36.307 is consistent with the ‘‘fundamental alteration’’ defense to the reasonable modifications requirement of § 36.302....
-
Section 36.302 Modifications in Policies, Practices, or Procedures (Section-By-Section Analysis and Response to Comments)
The rule enunciated in Sec.36.307 is consistent with the "fundamental alteration'' defense to the reasonable modifications requirement of Sec.36.302....
-
11B-407.4.8.2 Audible indicators
Audible indicators shall comply with Section 11B-407.4.8.2.
-
11B-407.4.3 Platform to hoistway clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1¼ inch (32 mm) maximum.
-
11B-411.2.1.3 Arrangement
Hall call console arrangement of required features shall comply with Section 11B-411.2.1.3.
-
11B-411.2.1.4 Additional features
Hall call console additional features, if provided, shall comply with Sections 11B-309 and 11B-411.2.1.4.
-
11B-411.2.1 Hall call consoles
Hall call consoles shall comply with Sections 11B-411.2.1 and 11B-309.
-
11B-409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (12.7 mm) under rated loading to zero loading conditions.
-
11B-411.4.7.2 Location
Raised characters or symbols and Braille designations shall comply with Section 11B-407.4.7.1.2.
-
11B-407.2.1.1 Height
Call buttons and keypads shall be located within one of the reach ranges specified in Section 11B-308, measured to the centerline of the highest operable part. Exception:...
-
409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (13 mm) under rated loading to zero loading conditions.
-
407.4.3 Platform to Hoistway Clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1¼ inch (32 mm) maximum.