Transfer supports for transfer surfaces complying with M301.2.3.1 and M302.2 shall be located on the short side (length) opposite the transfer side.
Search Results "Seat Designation"
Filters
Commonly Searched Documents
-
M305.2.1.1 End Transfer Supports
-
M305.2.2.2 Side Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.2 shall be 28 inches (710 mm) long minimum and shall be positioned along the width of transfer...
-
Requirement 6 -- Reinforced Walls for Grab Bars
[See subsections ...]
-
Alternative Designs. Bathroom as Shower Room
Alternative Designs. Bathroom as Shower Room....
-
KirbyBuilt Providence Picnic Table with Maximum Seating
Tabletop & Seats: Plastic - injection molded, ribbed and reinforced Tabletop Length: 6 ft....
-
Design Guidelines for Environmental Illness
There is no statutory authority for the Department to create the type of design and construction standards suggested by the commenters....
-
United States of America v. Quiktrip Corporation - Consent Decree
IN THE UNITED STATES DISTRICT COURT FOR THE DISTRICT OF NEBRASKA Omaha Division THE UNITED STATES OF AMERICA, Plaintiff, v. QUIKTRIP...
-
2013 Forest Service Trail Accessibility Guidelines (FSTAG)
Forest Service Trail Accessibility Guidelines (FSTAG) 2013 All Trails and Constructed Features Addressed in the FSTAG and FSORAG that are constructed or altered within...
-
407.4.7 Designations and Indicators of Car Controls
Designations and indicators of car controls shall comply with 407.4.7....
-
407.4.7 Designations and Indicators of Car Controls
Designations and indicators of car controls shall comply with 407.4.7....
-
1991 ADA Standards for Accessible Design
Justice 28 CFR Part 36 Nondiscrimination on the Basis of Disability by Public Accommodations and in Commercial Facilities Excerpt from 28 CFR Part 36: ADA Standards for Accessible Design...
-
4.3.9 Doorway Design
4.3.9 Doorway Design We did not obtain quantitative data on performance in our door use research. Thus there are no accommodation models for this topic....
-
Planning and Designing Outdoor Recreation Facilities for Horses
"Equestrian Design Guidebook for Trails, Trailheads, and Campgrounds," a comprehensive technical resource, details those elements of planning, design, and construction that are specific...
-
§ 38.159(d)(1) Design load
(1) Design load....
-
b) Historic Curb Ramp Design Standards
b) Historic Curb Ramp Design Standards 72....
-
Pilot Rock XT and XTH Series End Accessible Picnic Table - Using Steel Tops and Seats
Series Overview Model XT and XTH End Accessible Picnic Tables are designed and constructed specifically for heavy use areas where unusually difficult service may be required. ...
-
Pilot Rock UT and UTH Series End Accessible Picnic Table Using Steel Tops Seats
Model UT and UTH End Accessible Picnic Tables are designed for most public applications. Built rugged, but with less weight, easier to move. ...
-
(3) the City's curb ramp design standard
(3) the City's curb ramp design standard utilized between 1994 and 2004 pursuant to which it constructed curb ramps with a V inch lip at the base in violation of federal disability access...
-
M305.2.4.2 Non-Circular Cross Section
Transfer supports with non-circular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (100 mm) minimum and 4.8...
-
5.1.3 Transfer Surface Low Height Options for M301 and M302
5.1.3 Transfer Surface Low Height Options for M301 and M302 The Committee did not agree on a final low height recommendation. Rationale for final recommendation (more detail...
-
5.4.8 Transfer Support Gripping Surface Hazard Recommendation for M301 and M302
5.4.8 Transfer Support Gripping Surface Hazard Recommendation for M301 and M302 Description: Gripping surface hazards are sharp or abrasive elements that prevent an individual...
-
5.1.3 Transfer Surface Low Height
5.1.3 Transfer Surface Low Height. No agreement on final low height
-
5.1.2 Transfer Surface High Height
5.1.2 Transfer Surface High Height. The transfer surface should have an adjustable height range with an upper height measuring at least 25 inches.
-
5.1.1 Transfer Surface Height Adjustability
5.1.1 Transfer Surface Height Adjustability. The transfer surface should have an adjustable height in small virtually continuous increments.
