existing premises, occupied or to be occupied by a handicapped person, if the proposed modifications may be necessary to afford the handicapped person full enjoyment of the premises of a dwelling...
Search Results "Covered Multifamily Dwelling (FHA)"
Filters
Commonly Searched Documents
-
§100.203(a)
-
Turning Space [§304]
space is required in these accessible rooms and spaces: toilet and bathing facilities dressing, fitting, and locker rooms transient lodging guest rooms dwelling...
-
Alterations and Water Closet Clearances in Single-User Toilet Rooms With In-Swinging Doors (Section-by-Section Analysis)
To allow greater transfer options, section 604.3.2 of the 2010 Standards prohibits lavatories from overlapping the clear floor space at water closets, except in residential dwelling units...
-
KMA - Access Planner, Multi-Family Housing
design documents, perform construction site audits, generate written reports, and communicate with design and construction teams to support mandatory compliance with state and federal (ADA/FHA...
-
The Basis for the 2010 ADA Standards Pocket Guide
Learn the basis of the 2010 ADA Standards Pocket Guide
-
AJW Architectural Products U1511EA Series Automatic ADA Compliant Hand Dryer, Universal Voltage - Surface Mounted
Cover and Finish: U1511EA: Powder coated (white) formed steel alloy. Cover secured to base with theft resistant screws. U1511EA-SF: satin stainless steel cover....
-
12206(a)(1)
Transportation, the Chair of the Architectural and Transportation Barriers Compliance Board, and the Chairman of the Federal Communications Commission, shall develop a plan to assist entities covered...
-
12206(a)(1) In general
Transportation, the Chair of the Architectural and Transportation Barriers Compliance Board, and the Chairman of the Federal Communications Commission, shall develop a plan to assist entities covered...
-
NPRM
The NPRM asked whether the GFE requirement should be expanded to cover these systems....
-
Site Constraints
This is intended to cover altered facilities where limited space or other constraints preclude construction of a complying ramp....
-
A4.13.9 Door Hardware
To be effective, they should cover the door width, less approximately 2 in (51 mm), up to a height of 16 in (405 mm) from its bottom edge and be centered across the width of the door....
-
Title II Highlights (revised in 2008)
Who is covered by title II of the ADA II. Overview of Requirements III. "Qualified Individual with a Disability" IV. Program Access V. Integrated Programs VI. Communications VII....
-
§ 37.101(e) Demand Responsive System, Vehicle Capacity of 16 or Fewer
Entities providing demand responsive transportation covered under this section are not specifically required to ensure that new vehicles with seating capacity of 16 or fewer are accessible...
-
Bobrick 18" Straight Grab Bar Peened B-6806.99 x 18
Cover is 22-gauge (0.8mm), type 304 stainless steel with satin finish, 3 1/4" (85mm) diameter. Cover snaps over mounting flange to conceal screws....
-
Bobrick 48" Straight Grab Bar B-5806 x 48
Cover is 22-gauge (0.8mm), type 304 stainless steel with satin finish, 3 1/4" (85mm) diameter. Cover snaps over mounting flange to conceal screws....
-
Bobrick 24" Straight Grab Bar B-5806 x 24
Cover is 22-gauge (0.8mm), type 304 stainless steel with satin finish, 3 1/4" (85mm) diameter. Cover snaps over mounting flange to conceal screws....
-
Bobrick 24" Straight Grab Bar B-6806 x 24
Cover is 22-gauge (0.8mm), type 304 stainless steel with satin finish, 3 1/4" (85mm) diameter. Cover snaps over mounting flange to conceal screws....
-
Cal-Royal 300 Series Hydraulic Door Closers
Market Multi Size Adjustable Commercial Door Closer Sizes 1 Thru 4 and 3 Thru 6 Meeting Barrier Free Applications Hydraulic Door Closer with Standard Back Check Full Plastic Cover...
-
Bobrick 42" Straight Grab Bar Peened B-6806.99 x 42
Cover is 22-gauge (0.8mm), type 304 stainless steel with satin finish, 3 1/4" (85mm) diameter. Cover snaps over mounting flange to conceal screws....
-
Bobrick 36" Straight Grab Bar Peened B-6806.99 x 36
Cover is 22-gauge (0.8mm), type 304 stainless steel with satin finish, 3 1/4" (85mm) diameter. Cover snaps over mounting flange to conceal screws....
-
Bobrick 12" Straight Grab Bar Peened B-6806.99 x 12
Cover is 22-gauge (0.8mm), type 304 stainless steel with satin finish, 3 1/4" (85mm) diameter. Cover snaps over mounting flange to conceal screws....
-
Bobrick 24" Straight Grab Bar Peened B-5806.99 x 24
Cover is 22-gauge (0.8mm), type 304 stainless steel with satin finish, 3 1/4" (85mm) diameter. Cover snaps over mounting flange to conceal screws....
-
Bobrick 42" Straight Grab Bar Peened B-5806.99 x 42
Cover is 22-gauge (0.8mm), type 304 stainless steel with satin finish, 3 1/4" (85mm) diameter. Cover snaps over mounting flange to conceal screws....
-
Bobrick 18" Straight Grab Bar B-6806 x 18
Cover is 22-gauge (0.8mm), type 304 stainless steel with satin finish, 3 1/4" (85mm) diameter. Cover snaps over mounting flange to conceal screws....
