(Figure 8) An inertial profiler uses an accelerometer and a non-contacting sensor, such as a laser transducer, to measure height....
Search Results "Coin Slot Height"
Filters
Commonly Searched Documents
-
Road Roughness Measurements
-
M303.2.4 Equipment Clearances (Section-by-Section Analysis)
Due to the reorganization of the equipment clearances provision in the final rule, the knee and toe clearance requirements for the other equipment section have been renamed depth and height...
-
H. Your Obligation to Provide Services and Equipment
[Sec. 382.21(a)(4)] On-board wheelchairs must be equipped with footrests, armrests which are movable or removable, adequate occupant restraint systems, a backrest height that permits assistance...
-
III 3.11000 Insurance
ILLUSTRATION: An amusement park requires individuals to meet a minimum height requirement that excludes some individuals with disabilities for certain rides because of a limitation in its...
-
1023.9 Stairway identification signs
comply with Chapter 11B shall be located at the landing of each floor level, placed adjacent to the door on the latch side, in all enclosed stairways in buildings two or more stories in height...
-
Standards that measure needed physical or mental ability to perform a job
Possible accommodations might include lowering the shelf-height, providing a step stool or other assistive device....
-
11B-703.3.1 Dimensions and capitalization
dots in the same cell1 0.100 (2.5 mm) Distance between corresponding dots in adjacent cells1 0.300 (7.6 mm) Dot height...
-
11B-404.2.10 Door and gate surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (254 mm) bottom smooth surface height...
-
F226.1 General
Consider work surfaces that are flexible and permit installation at variable heights and clearances....
-
404.2.10 Door and Gate Surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (255 mm) bottom smooth surface height...
-
5.4.2.2 Transfer and Positioning Support Length Recommendations for Imaging Equipment with Transfer Surfaces
A positioning support (for transfer surfaces >24” deep) is to extend horizontally along the side of the patient scanning/imaging bed/table with a length of 12 to 16 inches and a height...
-
Using the ORAR Exceptions [F202.3, Exception 4 and 1016, Exceptions 1, 2, and 3]
instance, where traffic calming devices, gates, or other barriers are provided on a paved roadway, the ORAR must have a clear width of 36 inches and obstacles cannot exceed one-half inch in height...
-
Seat Width Evaluation
seat was the smallest of the platform seat widths available in this study and was suitable for many participants (the 25th through 95th percentiles) for their level, highest and lowest height...
-
Alterations
is defined as remodeling, renovating, rehabilitating, reconstructing, changing or rearranging structural parts or elements, changing or rearranging plan configuration of walls and full-height...
-
3.3 Equipment Barriers and Solutions
., a bright color against a dark background on the adjustment features, such as the weight amount or seat height and labels that are raised Some parts of the equipment stick...
-
The Purpose of FSORAG and FSTAG
included (scoping); what has to comply with the guidelines; definitions of terms; and technical requirements defining the physical characteristics of accessible features, such as width, height...
-
Car Controls [4.10.12]
Alignment for a side reach is often difficult at panels on the front of cars due to the limited maneuvering space; consider a maximum height of 48 inches for panels on the front of cars....
-
4.16.6 Dispensers
As a result, the dispenser was located 24" above the floor, 5" higher than the minimum height in ADAAG, and 42" from the rear wall (Figure 13), which would have been too high and too far...
-
Additional Features of Van-Accessible Parking Spaces
Vertical clearance of 98 inches minimum to accommodate van height at the vehicle parking space, the adjacent access aisle, and on the vehicular route to and from the van-accessible space...
-
11B-703.3.1 Dimensions and capitalization
1.6 mm) Distance between two dots in the same cell1 0.100 (2.5 mm) Distance between corresponding dots in adjacent cells1 0.300 (7.6 mm) Dot height...
-
11B-404.2.10 Door and gate surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (254 mm) bottom smooth surface height...
-
1010.1.9.8.1 Delayed egress locking system
Sign lettering shall be at least 1 inch (25 mm) in height and shall have a stroke of not less than 1/8 inch (3.2 mm). 6.4....
-
11B-404.2.10 Door and gate surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (254 mm) bottom smooth surface height...
-
11B-703.3.1 Dimensions and capitalization
dots in the same cell1 0.100 (2.5 mm) Distance between corresponding dots in adjacent cells1 0.300 (7.6 mm) Dot height...