Status indicators, including all locking or toggle controls or keys (e.g., Caps Lock and Num Lock keys), shall be discernible visually and by touch or sound.
Search Results "Tactile Map"
Filters
Commonly Searched Documents
-
407.6 Status Indicators
-
11B-703.4.1 Height above finish floor or ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
Issue 6: Pre-timed signals (an APS is more than a pushbutton)
The pushbutton locator tone in a pushbutton-integrated APS provides access to other information provided by the APS unit: the vibrotactile WALK; the tactile arrow for wayfinding; tactile...
-
11B-703.4.1 Height above finish floor or ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
11B-703.4.1 Height above finish floor or ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
11B-703.1.1.2 Inspection
Signs and identification devices shall be field inspected after installation and approved by the enforcing agency prior to the issuance of a final certificate of occupancy per...
-
§27.71(k)(6)(iv)(A) Contrast.
However, tactile symbols required by (k)(6)(iv)(B) are not required to comply with paragraph (k)(6)(iv)(A) of this section....
-
§ 27.71(k)(6)(iv)(A) Contrast
However, tactile symbols required by (k)(6)(iv)(B) are not required to comply with paragraph (k)(6)(iv)(A) of this section....
-
11B-216.1 General
signs identifying permanent rooms and spaces, directional and informational signs (except those relating to accessible means of egress), and entrance signs are not required to comply with tactile...
-
1007.6.5 Identification
Additionally, tactile signage complying with ICC A117.1 shall be located at each door to an area of refuge....
-
1003.2.13.5.5 Identification
Additionally, tactile signage complying with ICC A117.1 shall be located at each door to an area of refuge....
-
Fixed position maps and kiosks
Fixed position maps and kiosks Tactile maps can also be mounted on walls and pedestals in locations where visually impaired individuals will be likely to find and identify them....
-
Mounting Height and Location
Section 703.4 covers the mounting height and location of signs with tactile characters....
-
Designations: ADA Standard Section 216.2
Section 216.2 covers scoping requirements in the current ADA Standards for sign designations.
-
§382.57(c)(6) Input
(6) Input. Input devices must comply with paragraphs (c)(6)(i) through (iv) of this section.
-
§ 382.57(c)(6) Input
(6) Input. Input devices must comply with paragraphs (c)(6)(i) through (iv) of this section.
-
Stroke Thickness: ADA Standard Section 703.5.7
Stroke thickness of the uppercase letter “I” shall be 10 percent minimum and 30 percent maximum of the height of the character.
-
11B-703.5.7 Stroke thickness
Stroke thickness of the uppercase letter “I” shall be 10 percent minimum and 20 percent maximum of the height of the character. [2010 ADA Standards] 703.5.7 Stroke Thickness....
-
407.2.3.1 Floor Designation
Floor designations shall be provided in both tactile characters and braille. Tactile characters shall be 2 inches (51 mm) high minimum....
-
407.2.3.1 Floor Designation
Floor designations shall be provided in both tactile characters and braille. Tactile characters shall be 2 inches (51 mm) high minimum....
-
Figure 407.2.3.1 Floor Designations on Jambs of Elevator Hoistway Entrances – Drawing from the U.S. Access Board
-
Tactile letters
Tactile letters The map used a mixture of both serif and sans serif fonts for tactile letters. The font choice did not appear to be coordinated with different map features....
-
407.2.3.1 Floor Designation
Floor designations shall be provided in both tactile characters and braille. Tactile characters shall be 2 inches (51 mm) high minimum....
