Installation: Before installing grab bars, verify with all state and local codes for requirements on bar diameter and type finish....
Search Results "L-Shaped Grab Bar"
Filters
Commonly Searched Documents
-
AJW Architectural Products UG130-A Series UG130-A12 12" Exposed Flange, 1.5" Diameter Grab Bar - Configuration A
-
AJW Architectural Products UG120-A Series UG120-A12 12" Exposed Flange, 1.25" Diameter Grab Bar - Configuration A
Installation: Before installing grab bars, verify with all state and local codes for requirements on bar diameter and type finish....
-
Moen Stainless 30" Grab Bar
complies with Americans with Disabilities Act (ADA) specifications 30" bar length 1.25" bar diameter corrosion resistant stainless steel construction for added durability limited...
-
5.3.4 Grab Bars
Where walls or partitions are provided, grab bars complying with ABAAS section 604.5 shall be provided....
-
Comfort Designs Tamper Proof Anti-ligature Grab Bars
Tamper proof anti-ligature grab bars are designed to prevent tying of materials by eliminating space between wall and bar. Weep holes allow for water drainage....
-
604.5.1 Side Wall
The side wall grab bar shall be 42 inches (1065 mm) long minimum, located 12 inches (305 mm) maximum from the rear wall and extending 54 inches (1370 mm) minimum from the rear wall. ...
-
Inpro Corporation Endurant® Stainless Steel Straight Grab Bar
Grab bars offer a secure and safe experience. Many styles of ADA-compliant grab bars, safety supports, bath seats and coordinating accessories are available....
-
604.5.1 Side Wall
The side wall grab bar shall be 42 inches (1065 mm) long minimum, located 12 inches (305 mm) maximum from the rear wall and extending 54 inches (1370 mm) minimum from the rear wall. ...
-
604.9.4 Grab Bars
Grab bars for water closets shall comply with 604.5....
-
604.9.4 Grab Bars
Grab bars for water closets shall comply with 604.5....
-
AJW Architectural Products UG3-A Series UG3-A12 12" Concealed Snap Flange, 1.5" Diameter Grab Bar - Configuration A
Bars with greater offsets will support loads up to 250lbs when properly installed....
-
AJW Architectural Products UG2-A Series UG2-A12 12" Concealed Snap Flange, 1.25" Diameter Grab Bar - Configuration A
Bars with greater offsets will support loads up to 250lbs when properly installed....
-
11. Gap
Is the gap between the wall and the inside face of each grab bar exactly 1 1/2" to accommodate persons with disabilities who rest their forearms on the bars for stabilization so the arm...
-
8. Gap
Is the gap between the wall and the inside face of each grab bar exactly 1 1/2" to accommodate persons with disabilities who rest their forearms on the bars for stabilization so the arm...
-
609.3 Spacing
The space between the wall and the grab bar shall be 1½ inches (38 mm). The space between the grab bar and projecting objects below and at the ends shall be 1½ inches (38 mm) minimum....
-
Grab Bar Cross Sections
The Board has clarified that the space between grab bars and projecting objects below and at the ends shall be 1 ½ inches minimum, consistent with criteria for water closets, tubs, and showers...
-
609.3 Spacing
The space between the wall and the grab bar shall be 1½ inches (38 mm). The space between the grab bar and projecting objects below and at the ends shall be 1½ inches (38 mm) minimum....
-
11B-604.8.2.3 Grab bars
11B-604.8.2.3 Grab bars. Grab bars shall comply with Section 11B-609. A side-wall grab bar complying with Section 11B-604.5.1 shall be provided on both sides of the compartment....
-
Bradley Security Grab Bars SA70 Series
Intermediate supports are contour cut and joined by welding to form an integral part of the grab bar. All welds ground and polished to blend....
-
11B-804.2.2 U-Shaped
In U-shaped kitchens enclosed on three contiguous sides, clearance between all opposing base cabinets, counter tops, appliances, or walls within kitchen work areas shall be 60 inches (1524...
-
AJW Architectural Products UG30-A Series UG30-A12 12" Concealed Set Screw Flange, 1.5" Diameter Grab Bar - Configuration A
Flanges are heliarc welded to bar to form a one piece construction....
-
AJW Architectural Products UG20-A Series UG20-A12 12" Concealed Set Screw Flange, 1.25" Diameter Grab Bar - Configuration A
Flanges are heliarc welded to bar to form a one piece construction....
-
609.3 Spacing
The space between the wall and the grab bar shall be 1 1/2 inches (38 mm)....
-
609.3 Spacing
The space between the wall and the grab bar shall be 1 1/2 inches (38 mm)....
