The ADA Standards issued by the Department of Transportation (DOT) apply to facilities used by state and local governments to provide designated public transportation services, including bus...
Search Results "Bus Boarding Area"
-
Requirements to Remember for ADA Compliance in Construction Projects: Transportation Facilities
-
Americans with Disabilities Act (ADA) Standards for Transportation Facilities
DOT’s ADA Standards apply to facilities used by state and local governments to provide designated public transportation services, including bus stops and stations, and rail stations....
-
Bus boarding and alighting areas
Bus boarding and alighting areas must be in compliance with the ADA-ABA Guidelines (Section 810.2), which address surfaces (sturdy), dimensions (96" long x 60" wide); connection to sidewalks...
-
810.2.2 Dimensions--Modification to 810.2.2 of Appendix D to 36 CFR Part 1191
810.2.2 Dimensions--Modification to 810.2.2 of Appendix D to 36 CFR Part 1191 Bus boarding and alighting areas shall provide a clear length of 96 inches (2440 mm), measured perpendicular...
-
Section 810.2.2
Section 810.2.2 The Department recognizes that there will be some situations in which the full dimensions of a bus boarding and alighting area complying with the §810.2.2 may not be able...
-
Subpart B—Buses, Vans and Systems
-
T202.1 General
Non-rail vehicles shall provide at least one means of accessible boarding and alighting that serves each designated stop on the fixed route to which the vehicle is assigned....
-
T205.1 General
Non-rail vehicles shall provide illumination complying with T503 at ramps, bridgeplates, doorways, and boarding and alighting areas....
-
T207.2 Passenger Doorways
Handrails or stanchions shall be provided at passenger doorways in a configuration that permits grasping and use from outside the non-rail vehicle and throughout the boarding and alighting...
-
T208.2 Connection to Doorways
A passenger access route shall connect each wheelchair space to doorways that provide a means of accessible boarding and alighting in accordance with T208.2....
-
§ 38.155(a)
, and to continue using such handrails or stanchions throughout the boarding process....
-
T210.4 Location
Wheelchair spaces shall be located as near as practicable to doorways that provide a means of accessible boarding and alighting....
-
T215.1 General
Communication features on non-rail vehicles shall comply with T215.
-
T215.2.3 Doorways
Doorways that provide a means of accessible boarding and alighting shall be identified on the exterior of the non-rail vehicle by the International Symbol of Accessibility complying with...
-
T215 Communication Features
-
810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2440 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
Site Arrival Points, Entrances, and Egress
-
CHAPTER 4: BOARDING AND ALIGHTING
-
Bus boarding and alighting areas, BRT vehicles and stops/stations
ADA standards apply to buses and bus boarding and alighting areas as well as BRT vehicles and stops/stations. (DOT ADA Regulation 49 C.F.R....
-
T402.3 Installation and Operation
When used for boarding and alighting, ramps and bridgeplates shall be firmly attached to the non-rail vehicle to prevent displacement....
-
T402.9 Transitions
Vertical surface discontinuities at transitions from boarding and alighting areas to ramps and bridgeplates shall comply with T302.4....
-
T404 Level Boarding and Alighting
-
T404.2 Vehicle Floor and Boarding Platform Coordination
The design of non-rail vehicles shall be coordinated with the boarding platforms to minimize the gap between the vehicle floor and the boarding platforms....
-
T404.3 Ramps and Bridgeplates
Where the space between the floor of non-rail vehicles and a boarding platform is greater than 2 inches (51 mm) horizontally or 5/8 inch (16 mm) vertically when measured at 50 percent passenger...